KSB UPA Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 98

background image

5 Installation at Site

26 of 98

UPA / UPA S

3400.86/17-EN

WARNING

Laying electric cables at temperatures below zero degrees

Damage to the electric cable!

▷

Observe the minimum permissible temperature at the cable surface of -25 °C for
moving cables.

▷

Observe the minimum permissible temperature at the cable surface of -40 °C for
stationary cables.

NOTE

Do not expose the electric cable to direct sunlight.

NOTE

A separate name plate is included in the scope of supply.
This name plate must be attached in a clearly visible position outside the place of
installation, e.g. at the control panel, pipeline or mounting bracket.

NOTE

The motor lead is selected for submerged operation and must be completely
submerged, including the cable connector.
See order documentation for any other use!
For pump sets installed in VdS-approved sprinkler installations always refer to and
observe the applicable requirements stipulated by VdS (German association of
property insurance companies). In accordance with VdS 2025, the cable must be laid
in such a way that it is protected against short circuit and earth fault.

5.2 Preparing the installation

5.2.1 Checking the installation conditions

Prior to starting with the installation, check compliance with the particular
framework conditions required for a trouble-free operation of the submersible
borehole pump. To do so, verify the order data or delivery data against the
constructional plans, the operating conditions and the operating limits of the pump
set.

1.

Has this pump set been ordered for this particular installation position?
(

Section 5.2.2, Page 27)

2.

Does the material variant of the pump set match the operating conditions?

3.

Is appropriate flow along the motor provided? (

Section 6.2.4.6, Page 60)

4.

Can the required minimum submergence be ensured during operation?
(

Section 6.2.4.2, Page 57)

5.

Is the sand content of the fluid to be handled below the specified maximum?
(

Section 6.2.4.4, Page 60)

6.

Is the temperature of the fluid to be handled below the specified maximum?
(

Section 6.2.4.5, Page 60)

7.

If fluids liable to form deposits are handled, is temperature monitoring provided?
(

Section 5.7.2, Page 52)

8.

Will the motor lead and the cable connector be completely immersed in the fluid
to be handled? (

Section 5.2.7, Page 31)

«
...
24
25
26
27
28
...
»

Содержание UPA



































































































Отзывы:

Нет отзывов

Похожие инструкции для UPA

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: HABONIM Страницы: 9

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Talgil Страницы: 14

Бренд: Tadao Страницы: 2

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

Бренд: Motrona Страницы: 10

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Бренд: HQ Power Страницы: 23

Бренд: JASTEC Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды