KSB HPK-L Скачать руководство пользователя страница 50

Страница: 50 / 74

7 Servicing/Maintenance

50 of 74

HPK-L

1136.8/15-EN

WARNING

Thin metal foil used as carrier material in joint rings

Risk of injury (cuts)!

▷

Wear protective clothing.

▷

Always use an appropriate tool to remove joint rings.

Observe the general safety instructions and information. (

Section 7.1, Page 44)

For any work on the motor, observe the instructions of the relevant motor
manufacturer.

For dismantling and reassembly observe the exploded views and the general
assembly drawing.

In the event of damage you can always contact our service departments.

NOTE

After a prolonged period of operation the individual components may be hard to
pull off the shaft. If this is the case, use a brand name penetrating agent and/or - if
possible - an appropriate puller.

NOTE

We recommend placing a drip pan under the pump along its entire length to collect
any fluid escaping during dismantling.

7.4.2 Preparing the pump set

1. Interrupt the power supply and secure the pump against unintentional start-up.

2. Disconnect and remove all auxiliary pipework.

3. Remove the coupling guard.

4. Remove the coupling spacer, if any.

7.4.3 Removing the motor

NOTE

On pump sets with spacer-type couplings, the back pull-out unit can be removed
while the motor remains bolted to the baseplate.

WARNING

Motor tipping over

Risk of crushing hands and feet!

▷

Suspend or support the motor to prevent it from tipping over.

1. Disconnect the motor from the power supply.

2. Unbolt the motor from the baseplate.

3. Shift the motor to separate it from the pump.

7.4.4 Removing the back pull-out unit

On pump sets without spacer-type coupling, the motor has been removed.

The notes and steps stated in (

Section 7.4.1, Page 49) to

(

Section 7.4.3, Page 50) have been observed/carried out.

Содержание HPK-L











































































Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды

KSB HPK-L, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды