KSB HPK-L Скачать руководство пользователя страница 14

Страница: 14 / 74

3 Transport/Storage/Disposal

14 of 74

HPK-L

1136.8/15-EN

≤ 90 °

Fig. 3:

Transporting the pump set

≤ 90 °

Fig. 4:

Transporting the pump on the baseplate

CAUTION

Risk of pump (set) or bare shaft end hitting other objects

Damage to the ceramic plain bearing!

▷

Secure them properly.

3.3 Storage/preservation

CAUTION

Damage during storage due to humidity, dirt or vermin

Corrosion/contamination of the pump (set)!

▷

For outdoor storage cover the pump (set) or the packaged pump (set) and
accessories with waterproof material.

CAUTION

Wet, contaminated or damaged openings and connections

Leakage or damage to the pump!

▷

Clean and cover pump openings and connections as required prior to putting
the pump into storage.

If commissioning is to take place some time after delivery, we recommend that the
following measures be taken for pump (set) storage.

▪

Store the pump (set) in a dry, protected room where the atmospheric humidity is
as constant as possible.

▪

Rotate the shaft by hand once a month, e.g. via the motor fan.

If properly stored indoors, the pump set is protected for a maximum of 12 months.
New pumps/pump sets are supplied by our factory duly prepared for storage.

For storing a pump (set) which has already been operated, the shutdown measures
must be adhered to. (

Section 6.3.1, Page 42)

Содержание HPK-L











































































Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды

KSB HPK-L, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды