KSB HPK-L Скачать руководство пользователя страница 38

Страница: 38 / 74

6 Commissioning/Start-up/Shutdown

38 of 74

HPK-L

1136.8/15-EN

6.1.8 Heating up/keeping warm the pump (set)

CAUTION

Pump blockage

Damage to the pump!

▷

Prior to pump start-up, heat up the pump as described in the manual.

Observe the following when heating up the pump (set) and keeping it warm:

▪

Make sure that the temperature is increased continuously.

▪

Heating speed: max. 5 °C/min (5 K/min)

Fluid temperatures above

150 °C

When the pump is used for handling fluids at temperatures above 150 °C make sure
that the pump has been heated throughout before starting it up.

Temperature difference

The temperature difference between the pump's surface and the fluid handled must
not exceed 100 °C (100 K) when the pump is started up.

6.1.9 Start-up

DANGER

Non-compliance with the permissible pressure and temperature limits if the pump
is operated with the suction and/or discharge line closed.

Explosion hazard!

Hot or toxic fluids escaping!

▷

Never operate the pump with the shut-off elements in the suction line and/or
discharge line closed.

▷

Only start up the pump set with the discharge-side shut-off element slightly or
fully open.

DANGER

Excessive temperatures due to dry running or excessive gas content in the fluid
handled

Explosion hazard!

Damage to the pump set!

▷

Never operate the pump set without liquid fill.

▷

Prime the pump as per operating instructions.

▷

Always operate the pump within the permissible operating range.

CAUTION

Abnormal noises, vibrations, temperatures or leakage

Damage to the pump!

▷

Switch off the pump (set) immediately.

▷

Eliminate the causes before returning the pump set to service.

The system piping has been cleaned.

The pump, suction line and, if applicable, inlet tank have been vented and
primed with the fluid to be handled.

The lines for priming and venting have been closed.

Содержание HPK-L











































































Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды

KSB HPK-L, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды