KSB HPK-L Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 74

background image

7 Servicing/Maintenance

46 of 74

HPK-L

1136.8/15-EN

CAUTION

Increased wear due to dry running

Damage to the pump set!

▷

Never operate the pump set without liquid fill.

▷

Never close the shut-off element in the suction line and/or supply line during
pump operation.

CAUTION

Impermissibly high temperature of fluid handled

Damage to the pump!

▷

Prolonged operation against a closed shut-off element is not permitted
(heating up of the fluid).

▷

Observe the temperature limits in the data sheet and in the section on
operating limits. (

Section 6.2, Page 40)

While the pump is in operation, observe and check the following:

▪

The pump must run quietly and free from vibrations at all times.

▪

Check the shaft seal.

▪

Check the static sealing elements for leakage.

▪

Check the rolling element bearings for running noises.
Vibrations, noise and an increase in current input occurring during unchanged
operating conditions indicate wear.

▪

Monitor the correct functioning of any auxiliary connections.

▪

Cooling system
Take the pump out of service at least once a year to thoroughly clean the cooling
system.

▪

Monitor the stand-by pump.
To make sure that stand-by pumps are ready for operation, start them up once a
week.

▪

Monitor the bearing temperature.
The bearing temperature must not exceed 90 °C (measured on the outside of the
bearing bracket).

CAUTION

Operation outside the permissible bearing temperature

Damage to the pump!

▷

The bearing temperature of the pump (set) must never exceed 90 °C (measured
on the outside of the bearing bracket).

NOTE

After commissioning, increased temperatures may occur at grease-lubricated rolling
element bearings due to the running-in process. The final bearing temperature is
only reached after a certain period of operation (up to 48 hours depending on the
conditions).

«
...
44
45
46
47
48
...
»

Содержание HPK-L











































































Отзывы:

Нет отзывов

Похожие инструкции для HPK-L

Бренд: GE Страницы: 28

Бренд: ULTIMATE SPEED Страницы: 52

Бренд: Takagi Страницы: 27

Бренд: York Страницы: 204

Бренд: GEA Страницы: 337

Бренд: RainWater Harvesting Страницы: 3

Бренд: Rinnai Страницы: 2

Бренд: Cosmo Страницы: 48

Бренд: Dimplex Страницы: 64

Бренд: KBS Страницы: 86

Бренд: Wilo Страницы: 32

Бренд: Dirty Hand Tools Страницы: 20

Бренд: Clarke Страницы: 12

Бренд: Zodiac Страницы: 10

Бренд: Clarke Страницы: 12

Бренд: Yale Страницы: 130

Бренд: CTC Union Страницы: 164

Бренд: Speck Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды