KSB HPK-L Скачать руководство пользователя страница 40

Страница: 40 / 74

6 Commissioning/Start-up/Shutdown

40 of 74

HPK-L

1136.8/15-EN

CAUTION

Risk of freezing during prolonged pump shutdown periods

Damage to the pump!

▷

Drain the pump and the cooling/heating chambers (if any) or otherwise protect
them against freezing.

6.2 Operating limits

DANGER

Non-compliance with operating limits for pressure, temperature, fluid handled and
speed

Explosion hazard!

Hot or toxic fluid could escape!

▷

Comply with the operating data specified in the data sheet.

▷

Never use the pump for handling fluids it is not designed for.

▷

Avoid prolonged operation against a closed shut-off element.

▷

Never operate the pump at temperatures, pressures or rotational speeds
exceeding those specified in the data sheet or on the name plate unless the
written consent of the manufacturer has been obtained.

DANGER

Formation of a potentially explosive atmosphere inside the pump

Explosion hazard!

▷

When draining tanks take suitable measures to prevent dry running of the
pump (e.g. fill level monitoring).

6.2.1 Ambient temperature

CAUTION

Operation outside the permissible ambient temperature

Damage to the pump (set)!

▷

Observe the specified limits for permissible ambient temperatures.

Observe the following parameters and values during operation:

Table 14:

Permissible ambient temperatures

Permissible ambient temperature

Value

Maximum

40 °C

Minimum

See data sheet.

6.2.2 Minimum permissible speed

CAUTION

Plain bearing is overloaded

Damage to the bearings!

▷

Never use a speed of less than 800 rpm.

Содержание HPK-L











































































Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды

KSB HPK-L, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HPK-L

Отзывы:

Похожие инструкции для HPK-L

Бренды по названию

Популярные бренды