KSB HPK-L Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 74

background image

7 Servicing/Maintenance

48 of 74

HPK-L

1136.8/15-EN

7.2.2.3 Cleaning filters

CAUTION

Insufficient inlet pressure due to clogged filter in the suction line

Damage to the pump!

▷

Monitor contamination of filter with suitable means (e.g. differential pressure
gauge).

▷

Clean filter at appropriate intervals.

7.2.3 Lubrication and lubricant change of rolling element bearings

7.2.3.1 Grease lubrication

The bearings are supplied packed with high-quality lithium-soap grease.

7.2.3.1.1 Grease quality

We recommend using Petro-Canada Peerless LLG high-temperature grease or an
equivalent product for lubrication. Under unfavourable operating conditions, e.g.
high room temperature, high atmospheric humidity, dust-laden air, aggressive
atmosphere etc., check the bearings earlier. If required, clean and re-lubricate them,
preferably with Petro-Canada Peerless LLG.

Klüber Asonic HQ72-102 can be used as an alternative.

CAUTION

Mixing greases of differing soap bases

Changed lubricating qualities!

▷

Thoroughly clean the bearings.

▷

Adjust the re-lubrication intervals to the grease used.

7.2.3.1.2 Grease quantities

Bearing bracket

Bearings

Grease qty. per single

bearing

LP02

7307 BG

6.5 to 8 g

LP03

7307 BG

6.5 to 8 g

LP04

7309 BG

13 to 15.5 g

LP05

7313 BG

23 to 26 g

LP06

7315 BG

29 to 33 g

The grease quantity indicated must be used for each single bearing of a bearing pair.

7.2.3.1.3 Intervals

▪

Under suitable operating conditions the grease-lubricated bearings will run for
25,000 operating hours.

▪

Under unfavourable operating conditions (e.g. high room temperature, high
atmospheric humidity, dust-laden air, aggressive industrial atmosphere) check
the bearings earlier and clean and re-lubricate them, if required.

▪

Replace the rolling element bearings after 25,000 operating hours or 3 years of
continuous operation.

«
...
46
47
48
49
50
...
»

Содержание HPK-L











































































Отзывы:

Нет отзывов

Похожие инструкции для HPK-L

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Бренд: Zoeller Страницы: 10

Бренд: Tandem Страницы: 120

Бренд: Wacker Neuson Страницы: 44

Бренд: A.O. Smith Страницы: 62

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Nessie Plug&Spray NPS 1CS

Бренд: Danfoss Страницы: 12

Бренд: B+BTec Страницы: 20

Altherma EKHWE150A3V3

Бренд: Daikin Страницы: 10

Бренд: EBARA Страницы: 48

HYDROMATIC G2HX

Бренд: Pentair Страницы: 12

Бренд: Zenith Страницы: 12

Бренд: IceManCooler Страницы: 2

Taro HCS SJ Series

Бренд: Texmo Industries Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды