KSB HPK-L Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 74

background image

Contents

3 of 74

HPK-L

Contents

Glossary .................................................................................................................................................. 6

General.................................................................................................................................................... 7

Principles ........................................................................................................................................................... 7

Installation of partly completed machinery.................................................................................................... 7

Target group..................................................................................................................................................... 7

Other applicable documents............................................................................................................................ 7

Symbols ............................................................................................................................................................. 7

Key to safety symbols/markings....................................................................................................................... 8

Safety ...................................................................................................................................................... 9

General.............................................................................................................................................................. 9

Intended use ..................................................................................................................................................... 9

Personnel qualification and training............................................................................................................... 9

Consequences and risks caused by non-compliance with this manual ....................................................... 10

Safety awareness ............................................................................................................................................ 10

Safety information for the operator/user ..................................................................................................... 10

Safety information for maintenance, inspection and installation .............................................................. 10

Unauthorised modes of operation ................................................................................................................ 11

Explosion protection ...................................................................................................................................... 11
2.9.1

Marking .............................................................................................................................................. 11

Temperature limits............................................................................................................................. 11

Monitoring equipment...................................................................................................................... 12

Operating limits ................................................................................................................................. 12

Transport/Storage/Disposal ................................................................................................................ 13

Checking the condition upon delivery .......................................................................................................... 13

Transport......................................................................................................................................................... 13

Storage/preservation ...................................................................................................................................... 14

Return to supplier........................................................................................................................................... 15

Disposal ........................................................................................................................................................... 15

Description of the Pump (Set) ............................................................................................................. 16

General description ........................................................................................................................................ 16

Product information as per Regulation No. 1907/2006 (REACH)................................................................. 16

Designation..................................................................................................................................................... 16

Name plate...................................................................................................................................................... 16

Design details.................................................................................................................................................. 17

Configuration and function........................................................................................................................... 19

Noise characteristics ....................................................................................................................................... 20

Scope of supply............................................................................................................................................... 20

Dimensions and weights ................................................................................................................................ 21

Installation at Site ................................................................................................................................ 22

Checks to be carried out prior to installation............................................................................................... 22

Installing the pump set .................................................................................................................................. 22
5.2.1

Installation on the foundation.......................................................................................................... 23

Installation without foundation ....................................................................................................... 24

Piping .............................................................................................................................................................. 24
5.3.1

Connecting the piping....................................................................................................................... 24

Permissible forces and moments at the pump nozzles.................................................................... 26

Auxiliary connections......................................................................................................................... 27

Enclosure/insulation ....................................................................................................................................... 28

Checking the coupling alignment ................................................................................................................. 28

Aligning the pump and motor ...................................................................................................................... 30
5.6.1

Motors with adjusting screw............................................................................................................. 31

Motors without adjusting screw ....................................................................................................... 31

«
1
2
3
4
5
...
»

Содержание HPK-L











































































Отзывы:

Нет отзывов

Похожие инструкции для HPK-L

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: Gardena Страницы: 11

Бренд: Wanner Engineering Страницы: 16

Бренд: Nastec Страницы: 28

Бренд: York Страницы: 27

Бренд: York Страницы: 32

Бренд: AromaMist Страницы: 15

Бренд: Chiltrix Страницы: 54

Бренд: Truma Страницы: 36

Бренд: Wacker Neuson Страницы: 60

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

PE-2F-PW Series

Бренд: Little Giant Страницы: 2

Бренд: Tsurumi Pump Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды