KRUUSE 271390 Скачать руководство пользователя страница 17

IV. Operation Procedures 

 

When preparing to treat a patient:   

 
Step1: Push the POWER SWITCH to light the ON indicator (LED). 
Step2: Check the water. 
Step3: Select the needed Tip, make sure it is fully seated with the Handpiece. 
Step4: Set the POWER KNOB to the suitable level for the insert. 
Step5: Hold the Handpiece with the Tip end pointing up over a suitable 
            drain. Step on the foot control and allow water to run from the   
            handpiece for a few seconds until it flows without spurting. 
 

Caution: The above procedure should be repeated each time when an 

Tip is replaced into the handpiece. 

Caution: Make sure that the water spray is at the desired temperature 

and is reaching the working edge of the tip. 

 
Step6: Place the tip into the patient’s mouth and use the foot control to   
      activate the handpiece and water flow. 
 

When treating a patient:

 

1.  First position the patient comfortably on the patient chair.    Adjust the chair 

angle and/or position so that you can easily access to the patient's oral cavity. 

2.  Put the saliva ejector into patient's mouth to evacuate away excessive saliva 

and cleaning remainders. 

3.  Gently move patient's head so that the oral can be easily accessed with good 

direction as shown in the figure below. 

   

During the treatment, keep the angle between patient's tooth surface and the   

    Handpiece Insert as close to 15 degree as possible.    If the patient is not   
    comfortable during the treatment, try the following steps. 

A. When treating place where patient is very sensitive, try to increase the 

Handpiece movement speed on the surface. 

B. Treat less sensitive place first, return to sensitive areas later. 
C. If problem persist, reduce the output power intensity of the Handpiece. 

 

4.  Control the handpiece with the foot switch: The Foot control is designed to 

control the functions of the Handpiece in two ways as below: 

A With the foot held down on the foot control, the Handpiece is activated 

and water flows from the Handpiece . 

B.With the foot control released, both Handpiece and water flow are shut 

off. 

 

 

11

Содержание 271390
























Отзывы: