manualshive.com logo in svg

Krendl 4200-D, Руководство пользователя, Страница: 27 / 38

Поделиться
Скачать
Krendl 4200-D Скачать руководство пользователя страница 27

Rev. Date: 1/3/12

Page 24

MODEL #4200-D

TROUBLESHOOTING

WARRANTY

This unit is backed by a warranty for manufacturer’s defects.  If your machine needs service during

the warranty time period, call your supplier immediately.  DO NOT attempt to service the machine, as
this voids the warranty!

IMPORTANT

At any signs of trouble with your machine, stop immediately, disconnect power and call your sup-

plier.  Refer to the GENERAL MAINTENANCE  section of this manual for further details.  Always discon-
nect the electrical power before making any inspections or repairs.

TROUBLESHOOTING

PROBLEM

CORRECTIVE  ACTION

1.) Engine will not start

A. Check if battery charge is low.
B. Check terminals on battery for good connection.
C. See Engine Manufacturer’s Manual.

2.) Engine starts but there are no other

A. Check for loose or damaged wires, ground shorts.

machine functions - no electrical

which may be caused from machine vibration.

power to the front panel

B. Turn off all power to machine before opening the

panel box.

3.) Engine starts - but the blower will

A. Check to see if the blower clutch is operating

not operate

B. Check clutch electrical connections.
C. Check belts, adjust or replace as required.
D. Check battery, clutch will not cycle or will slip if

battery is not fully charged.

E. Check that blower can be turned by hand.  If not,

blower may be tied up.

F. Weak/Worn clutch- replace or rebuild as required.

4.) Insufficient air - clutch is operating

A. Check that the blower control valve isn’t fully open.

Close or adjust  the handle control as needed.
You should be able to get over 4 p.s.i. of air on
gauge. See illustration 13.

B. Check that the blower relief valve is not stuck open.

See illustration 14 on page 25.

C. Check if blower air filter and intake hose is clogged.

See illustration 13.

D. Check airstream and bypass air hose connec-

tions, clamps, etc.

Air Filter

Blower Control

Illustration 13

Содержание 4200-D







































Отзывы:

Нет отзывов