manualshive.com logo in svg

Krendl 4200-D, Руководство пользователя, Страница: 19 / 38

Поделиться
Скачать
Krendl 4200-D Скачать руководство пользователя страница 19

Rev. Date: 1/3/12

Page 16

MODEL #4200-D

6. When operating in 

Remote mode

, the 4-Position Selector Switch must be set to

 Remote

position. (See illustration 5 on page 15.)

7. Remote control hand pendant positions will be selected from the following:

BLOWER-FEED

- operates both 

blower 

and 

agitator-feed 

simultaneously

OFF

- (middle position) all functions stop

BLOWER

- operates the 

blower 

only

8. Use the Auxiliary Outlet on the Main Control Panel for supplying 

continuous

 power (while 

red

 Main

Disconnect Switch is ON) to accessories.

Stopping Your Machine:

1) Switch the remote switch to “AIR ONLY” and wait until the hose is clear of all material.
2) Let the engine run for a couple of minutes to cool down.
3) Turn the control switch on the remote control cord to the “off” position and unplug the remote control

cord from the panel.

4) Turn the key switch to the “off” position.

SAFETY NOTE:

DO NOT FILL THE HOPPER TO CAPACITY AT THE END OF THE DAY.  THE MATERIAL

WILL COMPRESS AND CAN CAUSE MACHINE LOCKUP DURING THE NEXT START-UP.

Mechanical Settings:

The controls of your machine contain the blower and slidegate controls to adjust your machine for

each application and type of fiber.  (See illustration 7 on page 17.)  

Blower control

 (air) and 

slidegate

(material feed) are adjusted according to:

TYPE OF MATERIAL:

Cellulose and  fiberglass have different textures and densities that
respond to machine settings.

HOSE:

Corrugations or roughness of interior surface, diameter, length and
elevation of hose will also require varying adjustments.

WEATHER CONDITIONS: Temperature and humidity may require day to day adjustment of

machine settings.

Blower Control and Slidegate General Settings:

Blower control can increase or decrease the amount of air in the system, affecting the velocity

(speed) and spread rate (coverage) of fiber.  (See illustration 7 on page 17.)  The blower control valve
is used for  controlling air pressure and amount of air flow.

Opening or closing slidegate (material feed) controls the amount of fiber dropping into the airlock

which changes the production rate (lbs. per hour).  (See illustration 7 on page 17.)  For calibration
purposes the scale located on the machine indicates how many inches the airlock slidegate is opened.

Содержание 4200-D







































Отзывы:

Нет отзывов