manualshive.com logo in svg

Krendl 4200-D, Руководство пользователя, Страница: 14 / 38

Поделиться
Скачать
Krendl 4200-D Скачать руководство пользователя страница 14

Rev. Date: 1/3/12

Page 11

MODEL #4200-D

INSTALLATION

MACHINE DRIVE AND TRUCK SPECIFICATIONS:

Your Model #4200-D Krendl Machine can be mounted in any truck and chassis configuration. We

recommend a minimum chassis rating of 26,000 GVWR. We also recommend a minimum 22 feet van
body. The body should have  a full width rear door. The Krendl Model #4200-D Machine can be mounted
anywhere in the truck body. The factory recommended position is shown in Illustration 3.

***INSTALLATION NOTE: It is very important that all of the doors be open for all engine pow-
ered machines. This is to provide proper ventilation to the engine. If unit location is different
than the factory recommended location, engine cooling problems may occur. This will void the
warranty on the machine and the engine!

TOOLS NEEDED:

CUSTOMER SUPPLIED ITEMS:

1/2” Heavy Duty Drill

1/2” Bolts, washers, locknuts for fastening machine

Drill Bits: 9/16” for bolts

3/16, 5/16 fuel lines for pick-up & return fuel (diesel)

Fork Lift (means to lift the machine)

fuel pump for diesel fuel

Pry Bars
Basic Wrenches
 5” hole saw & 2-1/2” hole saw

INSTALLATION INSTRUCTIONS:
Note: Make sure all shipping materials and accessories have been removed from inside the
machine before installing.

1) Locate and mount the engine control panel to the front of machine as shown in the picture below.

Note: The engine control panel may also be mounted to the truck wall in the position you
desire once the machine has been located on the truck.

a. Connect the plugins between the engine control panel and engine wire harness.
b. Remove front cover from engine control panel and locate panel on front of machine.
c. Once the engine control panel has been located, mark and drill two (2) 17/64” holes thru both

the panel and machine.

d. Bolt the control panel to the machine using the provided 1/4-20 hardware.

Engine Control Panel

Содержание 4200-D







































Отзывы:

Нет отзывов