#SLA-60 R.8 March 2022
Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces
OPERATING INSTRUCTIONS
41
displayed when the remote control is OFF.
•
The transmission indicator icon will flash and a single beep will
confirm the reception of the command
10.8.7 Pilot Ignition Selection (Intermittent
or Pilot-on-Demand)
This system has the option of a pilot-on-demand, allowing the system
to change from a spark-to-pilot system to the pilot-on-demand
option. The pilot-on-demand will keep the firebox warm and establish
a draft in the vent, which allows the main burner to ignite with less
air-flow disruption.
To select the preferred
1. Press the MENU button to activate the menu.
2. Using the UP and DOWN arrows, highlight the PILOT icon and
press SELECT.
3. Use the UP and DOWN arrows to turn the pilot-on-demand ON
or OFF, then press SELECT.
•
The transmission indicator icon will flash and a single beep will
be emitted from the control module indicating pilot-on-demand
feature has been activated. The remote control screen will
display the snowflake with text PILOT icon.
•
The transmission indicator icon will flash and a double beep will
be emitted from the control module indicating the pilot-on-
demand feature has been deactivated. The remote control will
not display the snowflake with text PILOT icon.
10.8.8 Flame Adjustment
This control system has (5) flame levels. Flame height will not be
adjustable for the first (10 )seconds when the appliance is turned ON.
The control system will remember the previous flame level setting
and will automatically adjust after (10) seconds.
To adjust the flame level,
1. Press the MENU button to activate the menu.
2. Using the UP and DOWN arrows, highlight the FLAME icon and
press SELECT.
3. Use the UP and DOWN arrows to adjust the flame level to desired
setting, then press SELECT.
The transmission indicator icon will flash and a single beep will confirm
the reception of the command
10.8.9 Thermostat Operation
The remote control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control a room’s comfort level.
This control system requires a two degree Fahrenheit or higher
temperature difference between the room temperature and set
temperature for the fireplace to turn on.
The system will remember the previous temperature setting when
thermostat mode is cycled ON or OFF.
To activate this function,
1. Press the MENU button to activate the menu.
2. Using the UP and DOWN arrows, highlight the THERMO icon and
press SELECT.
3. Use the UP and DOWN arrows to turn the THERMO ON or OFF, then
press SELECT. The SET TEMP will start blinking. Using the UP and
DOWN arrows, select the desired temperature and press SELECT.
•
If the thermostat function is on, the set temperature can be
adjusted at any time by pressing the UP and DOWN arrows.
•
As the room temperature approaches the set temperature, the
remote system will automatically adjust the flame height.
•
If the room temperature rises above the set temperature, the
fireplace will shut down the main burner. The fireplace will
turn back on after the room temperature drops below the set
temperature.
10.8.10 Fan Speed Control (optional)
The fan speed can be adjust through (3) speeds: HIGH, MEDIUM, LOW.
The fan is controlled by a timer built into the control module. After
the fireplace is turned ON, the timer will wait for (3) minutes before
turning on the fan. After the fireplace is turned OFF, the fan will
remain on for (12) minutes.
To activate this function,
1. Press the MENU button to activate the menu.
2. Using the UP and DOWN arrows, highlight the FAN icon and
press SELECT.
3. Use the UP and DOWN arrows to adjust to desired fan speed,
then press SELECT.
•
The transmission indicator icon will flash and a single beep will
confirm the reception of the command
10.8.11 AUX1 Function (Light Kit)
The light kit intensity can be adjusted through (4) levels: HIGH,
MEDIUM, LOW, and OFF.
The system will remember the previous AUX1 setting from the menu.
However, when the appliance is turned OFF, AUX1 function will be
turned off. AUX1 can be activated when the remote control is OFF.
When the appliance is turned back ON, the AUX1 setting will be
restored to the previous ON setting.
To activate this function,
1. Press the MENU button to activate the menu.
2. Using the UP and DOWN arrows, highlight the AUX1 icon and
press SELECT.
3. Use the UP and DOWN arrows to adjust to desired light kit
intensity.
•
The transmission indicator icon will flash and a single beep will
confirm the reception of the command.
•
