OPERATION
H550 AE
Rev.: 001
kortho
KGJ X18
8-23
Low ink level active
The output signal tells the host machine that a low ink situation has occurred and that a ink refill is required.
Set this to correspond to the required output level when the output is active. This signal can be set to be
active
High
or active
Low
.
Print missed action
This signal is activated when the printer receives a print signal while it the previous printcycle is still in
progress.
This parameter can be set to
Error
or
Warning
. When set to
Error
a missed print will abort the printing
process and the general alarm will be set. When set to
Warning
, the print process will continue when a
missed print is detected, a warning will be displayed on screen and depending on the
Multi function choice
setting, see below, the Warning output will be activated for 50ms (pulse).
Use line speed encoder?
This parameter can be set to
No
or
Yes
. When set to
No
the printer will print a fixed speed. This specific
speed can be set in the control unit, see subsection 8.6.6. When set to
Yes
, the printer will print at the speed
measured by the encoder that is connected to the control unit.
Note:
If an encoder is used for measuring the printspeed, the system will follow the measured speed
while printing. If the measured speed becomes zero (the substrate stops in front of the coding unit)
during the printprocess (trigger signal – print finished), the printer will stop printing. If the
substrate starts moving again within 30 seconds the printer will finish the print. If the substrate
stops for over 30 seconds the printprocess will be aborted i.e. the print will not be finished.
Ink out level active
The output signal tells the host machine that a low ink situation has occurred and the set amount of Low ink
prints have been made. I.e. that a ink refill is required. Set this to correspond to the required output level
when the output is active. This signal can be set to be active
High
or active
Low
.
Inhibit input active
When the inhibit input is activated, the system will not print. When this input is activated during the print
process, the print will be finished.
Trigger level
Select the rising edge (
High
) or falling edge (
Low
) of the trigger sensor. This setting depends on which type of
sensor is used and how it is set. A trigger sesor can be used to inform the printer about special events e.g. the
pallet is full so the label content should be updated or the next product should be marked with another label,
so it is required to load a new label.
8.6.4 Network settings
These settings make sure the system can be reached over the internal network and that communication
between e.g. PC (label design) and printer can take place.
To make sure the settings will match the network settings, always ask the network administrator for help
while integrating the printer into the company network.
Содержание GraphicJet X Series
