DIAGNOSTICS / TROUBLESHOOTING
H550 AE
Rev.: 001
kortho
KGJ X18
9-21
The user interface is
only showing a
blank screen.
Reset the control unit, by switching the control unit off and after
10 seconds on again.
9.3.2 Coding unit
Fault indication
Symptom(s)
Action(s)
After refilling the ink
the system, the
system does not
print anymore.
Assuming the control unit is not causing any problems, see
subsection 9.3.1: Prime the coding unit, to remove the air out of
the system.
The sytem is not
printing.
Assuming the control unit is not causing any problems, see
subsection 9.3.1:
Check whether the control unit indicates an error message. If so,
remove the cause of the error en reset the error message.
Chceck if all cables are connected properly.
Check whether a label is selected.
Check whether the system is in run mode.
Check whether the “print indicator” is lit while the system is
supposed to make a print.
Check whether a printsignal has been received by the control
unit (counter should be updated after a print signal has been
applied).
Check whether the photocell detects the substrate (LED on
photocell should switch off and on).
Make sure there is enough ink in the ink reservoir (only refill
when the ink low LED is lit!).
Prime the coding unit, to remove the air out of the system.
Purge the system, to see if the printhead is still ok. If not, replace
the head filter and check the print again.
Replace the printhead.
White lines are
shown in the print
direction
One or more nozzles are blocked or partially blocked. Clean the
frontplate of the printhead by squirting some solvent to the
frontplate (do not rub against the frontplate., this might damage
the frontplate and/or durt might be pushed into the nozzles
which will cause a permanent blockage of these nozzles).
Prime the coding unit, to remove the air out of the system.
Purge the system, to see if the printhead is still ok. If not, replace
the head filter and check the print again.
Replace the printhead.
Vertical white lines
are shown in the
print.
When using the internal encoder:
The set speed doesn’t matches the actual speed and/or the actual
speed is fluctuating too much. Set the speed at the right value
and/or make sure the substrate is moving at a stable speed.
When using an external encoder:
Make sure the specs of the encoder match the required system
specs.
Check whether the encoder is in constant contact with the
substrate and if there is no slip between the encoder wheel and
Содержание GraphicJet X Series
