Komatsu PC20R-8 Скачать руководство пользователя | Manualshive

Страница: 184 / 196

background image

182

AUTHORIZED OPTIONAL EQUIPMENT

6.1

AUTHORIZED OPTIONAL EQUIPMENT

6.1.1 PRECAUTIONS REGARDING SAFETY

CAUTION

•

Komastu Utility machines can be supplied with optional equipment in addition to the standard equip-
ment; if optional equipment is installed and used, carefully read the relevant operation manual and
keep to the instructions given therein.

•

Use exclusively optional or special equipment recommended and approved by Komastu Utility and
complying with the requisites indicated in the table (See “6.1.3 CHARACTERISTICS OF THE OPTIONAL
EQUIPMENT”).

•

Komastu Utility cannot be held liable for any damage, accident, reduction of the machine efficiency due
to the application and use of unauthorized equipment.

The installation of optional accessories and equipment other than those authorized by Komastu Utility negatively
affects the life of the machine, but can also cause problems concerning safety.
It is advisable to contact a Komastu Utility Dealer before installing any accessory not indicated in this operation
and maintenance manual.
In case of failure to comply with this rule, Komastu Utility declines any responsibility for accidents or damage.

DANGER

•

When removing or installing any equipment, take the following precautions and be careful to the safety
conditions.

•

Carry out installation and removal on a firm and flat surface.

•

When the operations are carried out by two or more operators, decide the communication signals in
advance and respect them during the operations.

•

Use a crane to handle objects weighing more than 25 kg.

•

Always support any heavy part before moving it. When heavy parts are lifted, be always careful to the
center of gravity of the object being handled.

•

It is very dangerous to carry out any operation with a suspended load, therefore, always position the
load on a support and make sure that it is in a safe position.

•

When installing or removing any equipment, make sure that it is stable and cannot fall down.

•

Do not stand under loads being lifted by a crane.
Take care to choose a safe position, where you do not run any risk in case the load should fall down.

IMPORTANT

☞

•

Specialized personnel is required to operate cranes. Do not allow non-specialized personnel to use
cranes.

For further details regarding installation and removal operations, contact your Komastu Utility Dealer.

«
...
182
183
184
185
186
...
»

Содержание PC20R-8





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC20R-8

Бренд: New Holland Страницы: 41

Бренд: Wacker Neuson Страницы: 298

Бренд: Daewoo Страницы: 668

Бренд: Kubota Страницы: 20

Бренд: Kubota Страницы: 165

Бренд: Greyhound Страницы: 61

Бренд: Ditch Witch Страницы: 107

PELLE RETRO PR-1500-P

Бренд: CHARGEUR Страницы: 25

Бренд: Komatsu Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды