Kohler 300EFOZCS Скачать руководство пользователя

Страница: 61 / 104

TP-7126 5/20

Section 2 Operation

I/O

Menu

Resistive Input

Analog Input 0:1
Analog Input 0:2
Analog Input 0:3
Analog Input 0:4
Analog Input 0:5
Analog Input 0:6

DESCRIPTION: (

function by default

unless modified via SiteTech

)

MEASUREMENT: ###.#Ohms

EVENT: *

INPUT ENABLED: ON/OFF*

SENSOR TYPE: *

LOW PROTECTIVE INHIBIT: ##s*

LOW WARNING: ON/OFF*

LOW WARNING LIMIT: *

LOW WARNING DELAY: ##s*

LOW SHUTDOWN: ON/OFF*

LOW SHUTDOWN LIMIT: *

LOW SHUTDOWN DELAY: ##s*

HIGH PROTECTIVE INHIBIT: ##s*

HIGH WARNING: ON/OFF*

HIGH WARNING LIMIT: *

HIGH WARNING DELAY: ##s*

HIGH SHUTDOWN: ON/OFF*

HIGH SHUTDOWN LIMIT: *

HIGH SHUTDOWN DELAY: ##s*

I/O

Menu (Continued)

Digital Input

Digital Input 0:1
Digital Input 0:2
Digital Input 0:3
Digital Input 0:4
Digital Input 0:5
Digital Input 0:6

DESCRIPTION: (

function by default

unless modified via SiteTech

)

STATUS: ACTIVE/INACTIVE

FUNCTION: *

EVENT: *

LOGIC: ACTIVE ON/ACTIVE OFF *

ENABLED: ON/OFF*

INHIBIT TIME: ##s*

DELAY TIME: ##s*

Digital Output

Digital Output 0:1
Digital Output 0:2
Digital Output 0:3
Digital Output 0:4
Digital Output 1:1

(Note: Only displayed if the 15-Relay

Dry Contact Kit is installed.)

...

DESCRIPTION:

(function by default

unless modified via SiteTech

)

STATUS: ACTIVE/INACTIVE

FUNCTION: *

EVENT: *

LOGIC: ACTIVE ON/ACTIVE OFF*

Active Events

Menu

Rotate the dial to view Active Events:

Warnings

Shutdowns

Statuses

Notices

See Section 2.6.3, Section 2.6.4, and

Section 2.6.5 for descriptions.

Press the OFF button to return to the

main menu.

* User-Defined (changeable) Menu Displays. Use SiteTech

software to change other settings including User-Defined Menu Displays.

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды