Kohler 300EFOZCS Скачать руководство пользователя

Страница: 66 / 104

TP-7126 5/20

66 Section 2 Operation

2.8 Monitoring and Programming

Setup

The user programmer can access the controller data

with the controller digital display or a personal computer

(PC) with optional SiteTech

software to monitor and/or

program. Access the controller system with a PC using

a USB cable with a mini USB plug. Refer to the

Introduction, List of Related Materials for related

software literature.

While this manual focuses on data access through the

controller pushbutton/rotary selector dial and display,

most data entries require input using a PC for initial

setup. The PC entries typically include alpha characters

such as digital input descriptions.

2.8.1

PC Communications

Communicate between a PC and the generator set

controller logic using USB communication protocol. The

PC connections require optional SiteTech

software.

Contact

your

authorized

distributor/dealer

for

assistance.

Local Single Connection

A PC connects to the USB port of the generator set

controller using a mini USB connector. See Figure 2-16.

Personal

Computer

Generator Set

Controller

USB Cable

Figure 2-16

Local Single Connection

Remote Single Connection

A modem connects a PC to a single device. The PC

communicates with the device via telephone line or an

ethernet network. See Figure 2-17.

Personal

Computer

with NIC

Ethernet

Network

Remote

Network

(Modem)

Modbus

Ethernet

Converter

Telephone

lines

Personal

Computer

Generator Set

Controller or

Transfer

Switch Control

Personal

Computer

with NIC

Ethernet

Network

Remote

Network

(Modem)

RS-232 to

RS-485 Port

Converter

Modbus

Ethernet

Converter

Telephone

lines

Personal

Computer

Generator Set

Controller or

Transfer

Switch Control

RS-485 up to 1220 m (4000 ft.)

Figure 2-17

Remote Single Connections

2.8.2

Modbus

Communications

The controller communicates using Modbus

as a slave

connection with the Modbus

master initiating the

communication. The controller seeks the system and

alternator parameters and diagnostic information then

responds back to the Modbus

master. In addition, the

controller accepts information to alter controller

parameters including generator set starting and

stopping. See Figure 2-18. Refer to the List of Related

Materials for available Modbus

literature.

Note:

Only one Modbus

master can be connected to

the controller. Examples include the remote

serial annunciator and switchgear applications.

Generator Set

Controller

Modbus

Master

RS-485

up to 1220 m (4000 ft.)

Figure 2-18

Modbus

Connections

Modbus

is a registered trademark of Schneider Electric.

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды