Kohler 300EFOZCS Скачать руководство пользователя

Страница: 35 / 104

TP-7126 5/20

Section 1 Specifications

1.8.2

Communication Setup Submenu

Modbus

Communications

The controller communicates using Modbus

as a slave

connection with the Modbus

master initiating the

communication. The controller seeks the system and

alternator parameters and diagnostic information then

responds back to the Modbus

master. In addition, the

controller accepts information to alter controller

parameters including generator set starting and

stopping. See Figure 1-9. Refer to the List of Related

Materials for available Modbus

literature.

Note:

Only one Modbus

master can be connected to

the controller. Examples include the remote

serial annunciator, monitoring software, and

switchgear applications.

Generator Set

Controller

Modbus

Master

RS-232

up to 15 m (50 ft.)

RS-485

up to 1220 m (4000 ft.)

Figure 1-9

Modbus

Connections

A controller can communicate directly to a Modbus

master or participate in a network of devices. It can also

be used to interface a local master to a network of

devices.

The Modbus

master polls slave devices for data.

Controller devices are slaves. Examples of master

devices are a personal computer running monitoring

software and the remote serial annunciator.

SiteTech

Group

Parameter

Setting

Modbus Address

Use a unique network address

between 1 and 247 for each unit.

Use 1 for a single connection.

Do not use 0 (zero).

Baud rate 9600, 19200, 38400, or 57600.

Must match the master PC and all

devices in the system.

Figure 1-10

Decision-Maker

3500 Communication

Parameters

Select the baud rate. Choose the same baud rate for the

Modbus

master, modems, and connected devices.

See Figure 1-10.

Each generator set controller must have a unique

Modbus

address and PGEN node number (1- 4).

Note:

The PGEN node number is automatically

determined. The number of nodes online should

match the number of installed generators.

Note:

The PGEN baud rate should not be adjusted

except under direction from a factory service

representative. Different baud rates between

controllers on the network will result in a loss of

communication on the network.

Modbus

is a registered trademark of Schneider Electric.

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды