Kohler 300EFOZCS Скачать руководство пользователя

Страница: 24 / 104

TP-7126 5/20

24 Section 1 Specifications

Engine Start Delay

displays the time delay before

the generator set starts while the master switch is in

AUTO or RUN positions.

Starting Aid Delay

displays the engine starting aid

activation time.

Crank On Delay

displays the time allocated for

generator set crank on in seconds.

Crank Pause Delay

displays the time allocated for

generator set crank pause in seconds.

Engine Warmed Up

displays the temperature

when the engine is warmed up enough to be

loaded.

Engine Cooled Down

displays the temperature

below which the engine cooldown can be

overridden.

Cooldown Delay

displays the time delay for

engine cooldown while the master switch is in the

AUTO or RUN positions and not in the idle mode.

Cooldown Override

allows the user to select the

Cooldown Temperature Override Mode. If set to

ON, the engine will stop immediately if the coolant

temperature is below the engine cooled threshold,

but will run for the duration of the cooldown cycle

otherwise. If set to OFF, the engine will always

complete the cooldown cycle.

Fuel Type

displays the programmer entered fuel

type as NG (Natural Gas), LP (Liquefied

Petroleum), Gasoline, Diesel, or Unknown.

Crank Cycles Limit

displays the programmer

entered crank cycle.

Enable NFPA Defaults:

Allows the user to Enable

or Disable the NFPA defaults.

Enable Emergency Battlemode:

Allows the user

to turn On/Off the emergency battlemode feature.

Note:

Conditional for certain units.

Protection Configuration

Note:

The time delays are user adjustable using

SiteTech

. Have setup and adjustments of

the

Decision-Maker

3500

controller

performed only by an authorized Kohler

distributor/dealer.

The

setup

and

adjustments are password protected.

Overvoltage

displays the percentage of the

system voltage that the generator voltage must

exceed for an overvoltage condition to be

indicated. The overvoltage value in volts is also

displayed.

Overvoltage Delay

displays the time that the

generator voltage must be in an overvoltage

condition before a fault is indicated.

Undervoltage

displays the percentage of the

system voltage that the generator voltage must

drop below for an undervoltage condition to be

indicated. The undervoltage value in volts is also

displayed.

Undervoltage Delay

displays the time that the

generator voltage must be in an undervoltage

condition before a fault is indicated.

Overfrequency

displays the percentage of the

system frequency that the generator frequency

must exceed for an overfrequency condition to be

indicated. The overfrequency value in Hz is also

displayed.

Underfrequency

displays the percentage of the

system frequency that the generator frequency

must drop below for an under frequency condition

to be indicated. The underfrequency value in Hz is

also displayed.

Overspeed

displays the percentage of the engine

speed that the engine must exceed for an

overspeed condition to be indicated.

The

overspeed value in Hz and RPM is also displayed.

Low Battery Voltage

displays the system battery

voltage that the battery voltage must drop below for

a low battery voltage condition to be indicated. The

low battery voltage in VDC is also displayed.

High Battery Voltage

displays the system battery

voltage that the battery voltage must exceed for a

high battery voltage condition to be indicated. The

high battery voltage in VDC is also displayed.

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды