Kohler 300EFOZCS Скачать руководство пользователя

Страница: 6 / 104

TP-7126 5/20

Safety Precautions and Instructions

Exhaust System

Carbon monoxide.

Can

cause

severe

nausea,

fainting, or death.

The exhaust system must be

leakproof and routinely inspected.

WARNING

Carbon

monoxide

symptoms.

Carbon monoxide can cause severe

nausea, fainting, or death.

Carbon

monoxide is a poisonous gas present in

exhaust gases. Carbon monoxide is an

odorless,

colorless,

tasteless,

nonirritating gas that can cause death if

inhaled for even a short time. Carbon

monoxide poisoning symptoms include

but are not limited to the following:

Light-headedness, dizziness

Physical fatigue, weakness in

joints and muscles

Sleepiness, mental fatigue,

inability to concentrate

or speak clearly, blurred vision

Stomachache, vomiting, nausea

If experiencing any of these symptoms

and carbon monoxide poisoning is

possible, seek fresh air immediately

and remain active. Do not sit, lie down,

or fall asleep.

Alert others to the

possibility

carbon

monoxide

poisoning. Seek medical attention if

the condition of affected persons does

not improve within minutes of breathing

fresh air.

Inspecting the exhaust system.

Carbon monoxide can cause severe

nausea, fainting, or death.

For the

safety of the craft’s occupants, install a

carbon monoxide detector.

Never

operate the generator set without a

functioning carbon monoxide detector.

Inspect the detector before each

generator set use.

Operating the generator set. Carbon

monoxide can cause severe nausea,

fainting, or death.

Be especially

careful if operating the generator set

when moored or anchored under calm

conditions

because

gases

may

accumulate. If operating the generator

set dockside, moor the craft so that the

exhaust discharges on the lee side (the

side sheltered from the wind). Always

be aware of others, making sure your

exhaust is directed away from other

boats and buildings.

Fuel System

Explosive fuel vapors.

Can cause severe injury or death.

Use extreme care when handling,

storing, and using fuels.

WARNING

The fuel system.

Explosive fuel

vapors can cause severe injury or

death.

Vaporized fuels are highly

explosive. Use extreme care when

handling and storing fuels. Store fuels

in a well-ventilated area away from

spark-producing equipment and out of

the reach of children. Never add fuel to

the tank while the engine is running

because spilled fuel may ignite on

contact with hot parts or from sparks.

Do not smoke or permit flames or

sparks to occur near sources of spilled

fuel or fuel vapors. Keep the fuel lines

and connections tight and in good

condition. Do not replace flexible fuel

lines with rigid lines.

Use flexible

sections to avoid fuel line breakage

caused by vibration. Do not operate the

generator set in the presence of fuel

leaks, fuel accumulation, or sparks.

Repair fuel systems before resuming

generator set operation.

Draining the fuel system. Explosive

fuel vapors can cause severe injury

or death.

Spilled fuel can cause an

explosion. Use a container to catch fuel

when draining the fuel system. Wipe up

spilled fuel after draining the system.

Hazardous Noise

Hazardous noise.

Can cause hearing loss.

Never operate the generator set

without a muffler or with a faulty

exhaust system.

CAUTION

Hazardous Voltage/

Moving Parts

Hazardous voltage. Moving parts.

Will cause severe injury or death.

Operate the generator set only when

all guards and electrical enclosures

are in place.

DANGER

Servicing the generator set when it

is operating. Exposed moving parts

will cause severe injury or death.

Keep hands, feet, hair, clothing, and

test leads away from the belts and

pulleys when the generator set is

running. Replace guards, screens, and

covers before operating the generator

set.

Grounding electrical equipment.

Hazardous voltage will cause severe

injury or death.

Electrocution is

possible

whenever

electricity

present. Ensure you comply with all

applicable codes and standards.

Electrically ground the generator set,

transfer switch, and related equipment

and electrical circuits. Turn off the main

circuit breakers of all power sources

before servicing the equipment. Never

contact electrical leads or appliances

when standing in water or on wet

ground because these conditions

increase the risk of electrocution.

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды