Kohler 300EFOZCS Скачать руководство пользователя

Страница: 34 / 104

TP-7126 5/20

34 Section 1 Specifications

generator is barely overloaded. If the load drops below

the Gen Overload Percent before a load priority is shed,

the accumulator for shedding load is reset.

Note:

Additional load control settings are provided in

SiteTech

, but they are configured during

commissioning

and

should

not

require

adjustment after commissioning is complete.

Have

setup

and

adjustments

the

Decision-Maker

3500 controller performed only

by an authorized Kohler distributor/dealer.

1.7.7

Emissions Information

(IMO Tier III Models Only)

Note:

Have emission information setup performed by

appropriately skilled and suitably trained

maintenance personnel familiar with generator

set operation and service.

The controller provides emissions related information

on selected generator sets. This information is intended

to provide the service technician data for maintaining

functionality and compliance with federal and local

emissions requirements.

Emissions

DEF Level.

The display provides the monitored Diesel

Exhaust Fluid (DEF) level expressed as a percentage

(0.0- 100.0%). The DEF is injected into the exhaust

where it is used in the Selective Catalyst Reduction

(SCR). The DEF fluid level must be monitored and

maintained by the user, refill the DEF tank as necessary.

EXHST OUT TEMP.

The display provides the

monitored exhaust outlet temperature expressed as

xxxxC/F degrees.

Notifications

The controller will receive messages from the engine

ECM. When important emissions related messages are

received, they will be indicated on the generator set

controller through the use of special symbols for IMO

Tier III engines.

These symbols are shown in

Figure 1-8. When one of these symbols is displayed,

refer to the specific engine event codes from the engine

ECM and refer to the engine operation manual.

High Exhaust Temperature.

This symbol indicates the

exhaust temperature is high when cleaning is in process

and indicates the system is functioning properly.

System Issue.

This symbol indicates something is

wrong with the exhaust or emissions control system.

Low DEF.

This symbol indicates the Diesel Exhaust

Fluid (DEF) level is low (steady) or extremely low

(flashing) and the DEF tank must be filled.

hh:hh

dd:mm:yy

EMISSIONS

HIGH EX TEMP SYSTEM ISSUE

LOW DEF

Figure 1-8

ECM Emissions Symbols

1.8 Controller Configuration Menu

1.8.1

Controller Configuration

Submenu

Language

displays the user selected language. At

this time, English is the only available option.

Units

displays the user selected unit of measure as

Metric or English.

Time Format

displays the user selected time

format as 12 hours or 24 hours.

Date Format

displays the user selected date

format as mm/dd/yyyy or dd/mm/yyyy.

Contrast

displays user selected resolution values

to improve digital display clarity.

Alarm Silence

displays the programmer selected

alarm silence method Always or Auto Only using

SiteTech

software.

The Always selection

activates the alarm horn in any of the

OFF/RESET- AUTO- RUN modes. The Auto Only

selection activates the alarm horn only when in the

Auto mode.

Note:

Press the Alarm Silence/Lamp Test button to

silence the alarm horn.

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды