Kohler 300EFOZCS Скачать руководство пользователя

Страница: 70 / 104

TP-7126 5/20

70 Section 3 Scheduled Maintenance

3.4 Generator Set Service Schedule

Note:

Have maintenance work, including battery service, performed by appropriately skilled and suitably trained

maintenance personnel familiar with generator set operation and service.

Perform Service at Intervals Indicated (X)

Reference

Section

Daily

Every 200

Hrs. or 3

Months

Every 500

Hrs. or 1

Year

Every

1000 Hrs.

or as

shown

Lubricating Oil System

Check the oil level

Eng. O/M

Change the oil

Eng. O/M

Clean the centrifugal oil cleaner

Eng. O/M

Change the oil filter(s)

Eng. O/M

Cooling System

Check the coolant level

Eng. O/M

Check the anticorrosion zinc anode(s)

Eng. O/M

Check the seawater outlet and clean as necessary

3.6

Check the function of the siphon break, if equipped

Check/replace the seawater pump impeller

[

Eng. O/M

Check the coolant antifreeze and corrosion protection

Eng. O/M

(At 1

start)

X (Every

2000 hrs.)

Minimum

every yr.

Change the coolant and clean the cooling system

Eng. O/M

X (Every

6000 hrs.)

Minimum

every 5 yrs.

Fuel System

Check the fuel level

Eng. O/M

Drain the water separating prefilter

Eng. O/M

X (Every

500 hrs.)

Change the fuel filters

Eng. O/M

X (Every

1000 hrs.)

Minimum

every 5 yrs.

Exhaust System

Inspect the exhaust system components

[

3.6

X (Before

operation)

Check the exhaust gas condition. If the exhaust is blue or black,

contact your local distributor/dealer

3.6

X (During

operation)

Clean the exhaust/water mixing elbow

[

3.6

Inspect the complete exhaust system

2.2, 3.6

X Minimum

every yr.

Engine and Mounting

Check for water, fuel, coolant, and oil leakage, rectify as necessary

[]

Check the drive belt

]

Eng. O/M

(At 1

start)

X Minimum

every yr.

Check/adjust valve clearances and unit injectors

Eng. O/M

X (1

time)

X (Every

2000 hrs.)

Change the reductant filters

Eng. O/M

Check the mounting bolts/vibromounts and tighten if necessary

Consult the battery manufacturer’s instructions

[

Consult your local distributor/dealer for service

]

Read the WARNING found at the beginning of the manual regarding moving parts

Should be performed by your local distributor/dealer

Содержание 300EFOZCS









































































































Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды

Kohler 300EFOZCS, Операция

Результаты поиска

Содержание 300EFOZCS

Отзывы:

Похожие инструкции для 300EFOZCS

Бренды по названию

Популярные бренды