background image

Dimming actuator

Electronic transformers with LV-LED

20 ... 100 W

Inductive capacitive mixed load is not permitted.

With setting "LED trailing edge phase control" the connection power for HV-LED lamps
and electronic transformers with LV-LED doubles.

Total power consumption

at 230 V

max. 600 W/VA

In the case of unbalanced load, an output may be loaded with a max of 350 W/VA (230 V)
as long as the permissible total power consumption is not exceeded.

Power consumption 110 V per output

Incandescent lamps

20 ... 150 W

HV halogen lamps

20 ... 150 W

HV-LED lamps

typ. 3 ... 30 W

Compact fl lamp.

typ. 3 ... 30 W

Inductive transformers

20 ... 150 VA

Inductive transformers with LV-LED

20 ... 50 VA

Electronic transformers

20 ... 150 W

Electronic transformers with LV-LED

20 ... 50 W

Inductive capacitive mixed load is not permitted.

With setting "LED trailing edge phase control" the connection power for HV-LED lamps
and electronic transformers with LV-LED doubles.

Total power consumption

at 110 V

max. 300 W/VA

In the case of unbalanced load, an output may be loaded with a max of 175 W/VA (110 V)
as long as the permissible total power consumption is not exceeded.

Power boosters

See power booster instructions

Connection

single stranded

0.5 ... 4 mm²

Finely stranded without conductor sleeve

0.5 ... 4 mm²

Finely stranded with conductor sleeve

0.5 ... 2.5 mm²

Fitting width

72 mm / 4 module

KNX

KNX medium

TP256

Commissioning mode

S-mode

Rated voltage KNX

DC 21 ... 32 V SELV

Current consumption KNX

15 mA

Connection mode KNX

device connection terminal

Dimming actuator, 4-gang, order no. 2174 00

Rated voltage

AC 110 ... 230 V ~

Mains frequency

50 / 60 Hz

Power loss

max. 8 W

Standby power

max. 1.4 W

Ambient temperature

-5 ... +45 °C

Storage/transport temperature

-25 ... +70 °C

12 / 16

32575362

10867485

04.12.2019

Содержание 2171 00

















Отзывы: