KNX 2171 00 страница 11 Скачать руководство пользователя

Страница: 11 / 16

Dimming actuator

Electronic transformers with LV-LED

20 ... 100 W

Inductive capacitive mixed load is not permitted.

With setting "LED trailing edge phase control" the connection power for HV-LED lamps
and electronic transformers with LV-LED doubles.

Power consumption 110 V per output

Incandescent lamps

20 ... 250 W

HV halogen lamps

20 ... 250 W

HV-LED lamps

typ. 3 ... 50 W

Compact fl lamp.

typ. 3 ... 50 W

Inductive transformers

20 ... 250 VA

Inductive transformers with LV-LED

20 ... 50 VA

Electronic transformers

20 ... 250 W

Electronic transformers with LV-LED

20 ... 50 W

Inductive capacitive mixed load is not permitted.

With setting "LED trailing edge phase control" the connection power for HV-LED lamps
and electronic transformers with LV-LED doubles.

Power boosters

See power booster instructions

Connection

single stranded

0.5 ... 4 mm²

Finely stranded without conductor sleeve

0.5 ... 4 mm²

Finely stranded with conductor sleeve

0.5 ... 2.5 mm²

Fitting width

72 mm / 4 module

KNX

KNX medium

TP256

Commissioning mode

S-mode

Rated voltage KNX

DC 21 ... 32 V SELV

Current consumption KNX

15 mA

Connection mode KNX

device connection terminal

Dimming actuator, 2-gang, order no. 2172 00

Rated voltage

AC 110 ... 230 V ~

Mains frequency

50 / 60 Hz

Power loss

max. 4 W

Standby power

max. 0.8 W

Ambient temperature

-5 ... +45 °C

Storage/transport temperature

-25 ... +70 °C

Power consumption 230 V per output

Incandescent lamps

20 ... 300 W

HV halogen lamps

20 ... 300 W

HV-LED lamps

typ. 3 ... 60 W

Compact fl lamp.

typ. 3 ... 60 W

Inductive transformers

20 ... 300 VA

Inductive transformers with LV-LED

20 ... 100 VA

Electronic transformers

20 ... 300 W

11 / 16

32575362

10867485

04.12.2019

Содержание 2171 00

















Результаты поиска

Содержание 2171 00

Отзывы:

Похожие инструкции для 2171 00

Бренды по названию

Популярные бренды

KNX 2171 00, Руководство пользователя

Результаты поиска

Содержание 2171 00

Отзывы:

Похожие инструкции для 2171 00

Бренды по названию

Популярные бренды