manualshive.com logo in svg

KNX 2171 00, Руководство пользователя

Поделиться
Скачать
KNX 2171 00 Скачать руководство пользователя страница 15

Dimming actuator

Enable manual control.

Output cannot be operated.

Cause 1: Manual control has not been programmed.

Reprogram device.

Cause 2: Manual control via bus disabled.

Enable manual control.

None of the outputs can be operated.

Cause 1: All of the outputs are disabled-

Cancel disabling.

Cause 2: Manual mode active.

Deactivate manual mode (switch off continuous manual mode).

Cause 3: Application software missing or faulty.

Check programming and correct.

Cause 4: Application software has been stopped, programming LED is flashing.

Disconnect device from the bus and mains, switch on again after 10 seconds.

All outputs off and not possible to switch on

Cause 1: bus voltage failure.

Check bus voltage.

Cause 2: mains voltage failure.

Check mains voltage on outputs and mains power supply.

Luminaires flicker or buzz, proper dimming not possible, device buzzes

Cause: wrong dimming principle set

Installation or commissioning error. Disconnect device and luminaire, switch off circuit
breaker.
Check installation and correct.
If the wrong dimming principle has been preselected: Set correct dimming principle.
If dimming actuator calibrates itself incorrectly, e.g. with highly inductive mains or long
load cables: preselect correct dimming principle with commissioning.

LED lamp is dimly lit when dimmer is switched off

Cause: LED lamp is not optimally suited for this dimmer.

Use a compensation module, see accessories.
Use another type of LED lamp or an LED lamp of another manufacturer.

Light switches on at maximum brightness and then dims to the target value.

Cause: Device is programmed as a speed controller.

Reprogram device.

When using as a speed controller: Motor does not start

Cause: Device is programmed as a dimmer.

Switch off device immediately.
Reprogram device.

When using as a speed controller: Motor stops at low speed

Cause: Set base speed is too low.

Commissioning error. Switch off device.
Reprogram device. Readjust base speed (see chapter 5.2. Commissioning).

15 / 16

32575362

10867485

04.12.2019

Содержание 2171 00

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды