KNX 2171 00 страница 13 Скачать руководство пользователя

Страница: 13 / 16

Dimming actuator

Power consumption 230 V per output

Incandescent lamps

20 ... 250 W

HV halogen lamps

20 ... 250 W

HV-LED lamps

typ. 3 ... 50 W

Compact fl lamp.

typ. 3 ... 50 W

Inductive transformers

20 ... 250 VA

Inductive transformers with LV-LED

20 ... 100 VA

Inductive transformers

20 ... 250 VA

Electronic transformers with LV-LED

20 ... 100 W

Inductive capacitive mixed load is not permitted.

With setting "LED trailing edge phase control" the connection power for HV-LED lamps
and electronic transformers with LV-LED doubles.

Power consumption 110 V per output

Incandescent lamps

20 ... 120 W

Incandescent lamps

20 ... 120 W

HV halogen lamps

20 ... 120 W

HV-LED lamps

typ. 3 ... 24 W

Compact fl lamp.

typ. 3 ... 24 W

Inductive transformers with LV-LED

20 ... 50 VA

Electronic transformers

20 ... 120 W

Electronic transformers with LV-LED

20 ... 50 W

Inductive capacitive mixed load is not permitted.

With setting "LED trailing edge phase control" the connection power for HV-LED lamps
and electronic transformers with LV-LED doubles.

Power boosters

See power booster instructions

Connection

single stranded

0.5 ... 4 mm²

Finely stranded without conductor sleeve

0.5 ... 4 mm²

Finely stranded with conductor sleeve

0.5 ... 2.5 mm²

Fitting width

144 mm / 8 module

KNX

KNX medium

TP256

Commissioning mode

S-mode

Rated voltage KNX

DC 21 ... 32 V SELV

Current consumption KNX

15 mA

Connection mode KNX

device connection terminal

6.2 Troubleshooting

Connected LED lamps or compact fluorescent lamps switch off in the lowest dimming position
or flicker

The set minimum brightness is too low.
Increase minimum brightness.

Connected LED lamps or compact fluorescent lamps flicker

Cause 1: Lamps are not dimmable.

13 / 16

32575362

10867485

04.12.2019

Содержание 2171 00

















Результаты поиска

Содержание 2171 00

Отзывы:

Похожие инструкции для 2171 00

Бренды по названию

Популярные бренды

KNX 2171 00, Руководство пользователя

Результаты поиска

Содержание 2171 00

Отзывы:

Похожие инструкции для 2171 00

Бренды по названию

Популярные бренды