background image

Dimming actuator

Status indication

The status LED A1… (5) indicate the states of the outputs.

Off: Output switched off

On: Output switched on

Flashes slowly: Output in manual mode

Flashes quickly: Output disabled via continuous manual mode

Operating modes

Bus operation: Operation via push-button sensors or other bus devices

Short-term manual operation: Manual operation locally with button field, automatic return
to bus operation.

Continuous manual mode: Exclusively manual operation on the device

No bus operation is possible in manual mode.

No manual mode is possible in case of bus failure.

After a bus failure and restoration the device switches to bus operation.

After a power failure and restoration the device switches to bus operation.

The manual mode can be disabled in ongoing operation via a bus telegram.

Switching on the temporary manual control

Operation using the button field is programmed and not disabled.

Press the 

c

 button briefly.

LED A1 flashes, LED 

c

 remains off.

After 5 seconds without a button actuation, the actuator returns automatically to bus oper-
ation.

Switching off temporary manual operation

The device is in short-term manual mode.

No button-press for 5 seconds.
- or -

Press 

c

 button briefly as many time as necessary until the actuator leaves the short-time

manual mode.
LEDs A1... no longer flash, but rather indicate the output status.

Switching on permanent manual control

Operation using the button field is programmed and not disabled.

Press the 

c

 button for at least 5 seconds.

LED 

c

 is illuminated, status LED A1 flashes, continuous manual mode is switched on.

Switching off permanent manual control

The device is in continuous manual mode.

Press the 

c

 button for at least 5 seconds.

LED 

c

 is off, bus operation is switched on.

Operating the outputs

The device is in continuous or short-term manual mode.

Press the 

c

 button briefly as many times as necessary until the desired output is selec-

ted.
The LED of the selected output A1... flashes.

The LEDs ON/

n

 and OFF/

o

 indicate the status.

4 / 16

32575362

10867485

04.12.2019

Содержание 2171 00

















Отзывы: