Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Страница: 7 / 86

vii
List of Figures
Figure 1-1:
The HydroChart 3500 Sonar System Components . . . . . . . . . . . . . . . . . . . . 1-3
Figure 3-1:
LAN Cable, Navigation Cable Pigtail and AC and DC Power Cords . . . . . 3-2
Figure 3-2:
Sonar Head Unit Mounting Flange and Bolt Circle . . . . . . . . . . . . . . . . . . 3-3
Figure 3-3:
Arrow Label on the Sonar Head Unit Mounting Flange Should Point
toward the Bow
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Figure 3-4:
TIU Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Figure 3-5:
The Sonar Interface Dialog Box—System Control Tab . . . . . . . . . . . . . . . 3-10
Figure 4-1:
Removing the Phillips Head Screws from the Top of the Forward and Aft
Fairings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-2:
Removing the Phillips Head Screws from the Skid Plate . . . . . . . . . . . . . . . 4-3
Figure 4-3:
Sliding a Fairing off the Sonar Head Unit Frame . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-4:
Sonar Head Unit Frame with Fairings Removed . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-5:
Cables Disconnected from Sonar Electronics Housing . . . . . . . . . . . . . . . . 4-4
Figure 4-6:
Socket Head Cap Screws Securing the Transducer Arrays . . . . . . . . . . . . . 4-5
Figure 4-7:
Tightening the Socket Head Cap Screws in the Sonar Electronics Housing . . . .
Connector End Cap
4-5
Figure 4-8:
10-mm diameter, 1.5-mm Pitch Threaded Rod Screwed into the Connector
End Cap
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-9:
Pulling the Sonar Electronics Chassis out of the Sonar Electronics
Housing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-10:
Aligning and Installing the Connector End Cap . . . . . . . . . . . . . . . . . . . . . 4-7
Figure 4-11:
Sonar Electronics Housing Connector End Cap Connectors . . . . . . . . . . . 4-8
Figure 4-12:
Sonar Head Unit Fully Assembled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Figure 4-13:
Loosening the M6 Set Screw Securing the Sound Velocity Sensor . . . . . . 4-10
Figure 4-14:
Removing the Sound Velocity Sensor and its Adapter Sleeve . . . . . . . . . . 4-10
Figure 4-15:
Disconnecting the Sound Velocity Sensor Cable from the S/V Connector
on the Electronics Housing End Cap
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Figure 4-16: Sound Velocity Sensor Removed from its Adapter Sleeve. . . . . . . . . . . . . . 4-11