Klein Marine Systems, Inc. HYDROCHART 3500 страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 86

background image

ii

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

This document contains proprietary information, and such information may not be
disclosed to others for any purpose or used for any manufacturing purpose without
expressed written permission from Klein Marine Systems, Inc. (KMS). The
information provided is for informational purposes only and is subject to change
without notice. KMS assumes no responsibility or liability for any errors,
inaccuracies or omissions that may be present in this document.

The SonarPro software program may be used or copied only in accordance with
the terms of the Software License Agreement.

©

Copyright 2012–2017 by Klein Marine Systems, Inc. All rights reserved.

SonarPro

®

is a registered trademark of Klein Marine Systems, Inc.

HydroChart

®

is a registered trademark of Klein Marine Systems, Inc.

Windows XP

®

and Windows 7

®

are registered trademarks of Microsoft

Corporation.

Kevlar

®

is a registered trademark of the DuPont Company.

CARIS

®

is a registered trademark of CARIS.

HYPACK

®

is a registered trademark of HYPACK, Inc.

«
1
2
3
4
...
»

Содержание HYDROCHART 3500























































































Отзывы:

Нет отзывов

Похожие инструкции для HYDROCHART 3500

Бренд: Furuno Страницы: 95

Бренд: Velleman Страницы: 3

Бренд: Eagle Страницы: 56

Бренд: Raymarine Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды