Klein Marine Systems, Inc. HYDROCHART 3500 страница 21 Скачать руководство пользователя

Страница: 21 / 86

2-1

CHAPTER 2: S

PECIFICATIONS

This chapter includes the physical and performance specifications for the
HydroChart 3500 Sonar System Sonar Head Unit, TIU and deck cable. The Sonar
Head Unit connects to the TIU using the deck cable.

2.1

Sonar Head Unit

Deployment method:

Over the side or optional hull mount

Sonar frequency:

455 kHz

Sonar channels:

Transmission pulse width:

Wideband FM chirp at 4 msec

Bathymetry coverage:

10–12 times altitude

Resolution along-track
(bathymetry):

0.4



Resolution across-track
(bathymetry):

5.0 cm (2.0 in.)

Resolution along-track
(side scan):

0.21



Resolution across-track
(side scan):

1.5 cm (0.6 in.)

Range:

Up to 175 m (574 ft) per side

Construction:

Hard coat anodized high grade aluminum
with plastic fairing

Size:

94.5 cm (37.2 in.) long
27.9 cm (11.0 in.) wide
27.7 cm (10.9 in.) high

Maximum operating altitude:

50 m (164 ft)

Operating temperature:

-2–32



C (29–90



Weight in air:

27 kg (60 lb)

NOTE

These specifications are subject to change without notice. Actual

performance may also vary depending on the environmental and operating
conditions.

Содержание HYDROCHART 3500























































































Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды