manualshive.com logo in svg

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Klein Marine Systems, Inc. HYDROCHART 3500 Скачать руководство пользователя страница 25

3-1

CHAPTER 3: S

ETUP

 

AND

 T

EST

The HydroChart 3500 Sonar System is designed to be easily set up and deployed. 
This chapter provides instructions on how to unpack the system components, set 
them up, and turn on and test the system. Descriptions of all the connectors and the 
power on/off control and indicator on the TIU are also included.

3.1

Unpacking and Inspection

The HydroChart 3500 Sonar System is shipped in two corrugated cardboard boxes. 
One contains the deck cable, and the other contains the Sonar Head Unit, the TIU 
and all the other items listed below. Before unpacking the containers, carefully 
inspect them for damage. If any damage is found, immediately contact Klein 
Marine Systems, Inc. or your KMS sales representative 

and report the damage to the 

freight carrier. 

After unpacking the containers, inspect all the items for damage and 

check the packing list to ensure that all the items are included. If any damage is 
found or any items are missing, immediately contact Klein Marine Systems, Inc. or 
your KMS sales representative

. Also report any damage to the freight carrier. Do not 

install or operate any equipment that appears to be damaged.

The HydroChart 3500 Sonar System, as a minimum, includes the following 
components:

• Sonar Head Unit
• TIU
• Deck cable
• Software and documentation CD
• LAN cable
• Navigation cable pigtail
• AC  power  cord

• DC  power  cord

The Sonar Head Unit, the TIU and the deck cable are shown in Figure 1-1 on 
page 1-3. The LAN cable, the navigation cable pigtail and the AC and DC power 
cords are shown in Figure 3-1.

3.2

Locating the Topside Interconnect Unit

The TIU is sealed against spray and inclement weather. However, for equipment 
longevity, it is best to locate the TIU in a sheltered area.

Содержание HYDROCHART 3500























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды