Klein Marine Systems, Inc. HYDROCHART 3500 Скачать руководство пользователя | Manualshive

Страница: 15 / 86

background image

xv

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

ENTIRE AGREEMENT:

This License Agreement sets forth the entire

understanding and agreement between you and KMS supersedes all prior
agreements, whether written or oral, with respect to the Software, and may be
amended only in a writing signed by both parties.

Preface

The HydroChart 3500 Sonar System is a lightweight, portable side scan sonar
system comprising a Sonar Head Unit, a deck cable and a topside unit that
connects to a PC and a navigation device.

What’s in This Manual

This operations and maintenance manual provides information pertaining to the
setup and deployment, operation and general maintenance of the HydroChart 3500
Sonar System. The manual is divided into the following six chapters and five
appendices:

Chapter 1: Overview.

Presents an overview of the HydroChart 3500 Sonar

System components.

Chapter 2: Specifications.

Provides physical and performance

specifications for the main components of the HydroChart 3500 Sonar System.

Chapter 3: Setup and Test.

Provides instructions on how to unpack the

HydroChart 3500 Sonar System components, set them up, and turn on and test
the system.

Chapter 4: Maintenance.

Provides instructions for maintaining the

HydroChart 3500 Sonar System on a daily, a weekly and a long term basis.

Chapter 5: Technical Description.

Provides an overall description of the

HydroChart 3500 Sonar System electronics to assist in troubleshooting, repair
or adding optional equipment.

Chapter 6: System Troubleshooting.

Provides some troubleshooting

recommendations that should be followed if operational problems occur with
the HydroChart 3500 Sonar System.

Appendix A: Sonar Uncertainty Model.

Provides a description of the Klein

Marine Systems sonar uncertainty model.

Appendix B: Configuring and Updating the Sonar Head Unit:

Provides

instructions on how to use Linux TPU Updater to configure and update the
Sonar Head Unit.

Appendix C: Compass Calibration.

Provides a procedure on how to

calibrate the compass to account for differing magnetic fields.

«
...
13
14
15
16
17
...
»

Содержание HYDROCHART 3500























































































Отзывы:

Нет отзывов

Похожие инструкции для HYDROCHART 3500

Бренд: Furuno Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды