Klein Marine Systems, Inc. HYDROCHART 3500 Скачать руководство пользователя

Страница: 47 / 86

Removing and Installing the Optional Sound Velocity Sensor

4-9

4.4

Removing and Installing the Optional Sound

Velocity Sensor

Should it be required to replace the optional sound velocity sensor, it can be
accessed from under the sonar head after removing the forward fairing.

The following tools are recommended:

• 3-mm hex key

• Phillips screw driver

4.4.1 Removing the Sound Velocity Sensor

To remove the sound velocity sensor:

Perform Steps 1 through 5 in “Disassembling the Sonar Head Unit” on page 4-2.
However, remove only the forward fairing.

Place the Sonar Head Unit on its side to enable access to the underside of the
frame.

Figure 4-12:

Sonar Head Unit Fully Assembled

Содержание HYDROCHART 3500























































































Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды