Lowrance DSI Скачать руководство пользователя

Страница: 1 / 22

Traditional Sonar and DSI Sonar Installation

This document covers the installation of the transducer and display unit installation, which includes con-

necting the unit to power and installing the unit on the bracket mount.
The first section of the document covers the installation of a traditional sonar skimmer transducer. DSI

sonar installation is covered in the last section of the manual.

Make sure you read all the installation instructions before drilling holes in your vessel!

Traditional Sonar Transducer Installation

One piece bracket (Recommended Tools and Supplies — not included)

Drill

Marine grade above-or-below waterline sealant

1” (25mm) or 5/8” (15mm) drill bit

Marine grade epoxy (Shoot-thru-hull install only)

#29 (0.136”) (3mm) drill bit

Zip ties (trolling motor mount)

Phillips (Slotted-head) screwdriver

TMB-S bracket kit (Skimmer trolling motor mount)

NOTE

This majority of this installation does not apply to the GPS only units since they do

not have a transducer. Turn to pages 8-11 for information on mounting the display unit and

connecting the unit to power.

0.TWEETY INSTALL_SONAR_DSI.indd 1

9/14/2011 11:55:30 PM

Содержание DSI






















Результаты поиска

Содержание DSI

Отзывы:

Похожие инструкции для DSI

Бренды по названию

Популярные бренды

Lowrance DSI, Руководство по установке

Результаты поиска

Содержание DSI

Отзывы:

Похожие инструкции для DSI

Бренды по названию

Популярные бренды