Lowrance DSI Скачать руководство пользователя

Страница: 3 / 22

Traditional Sonar

3. Hold the transducer

assembly against

the transom. Look at

the transducer from

the side. If it is par-

allel to the ground,

then the “A” position

is correct.

4. If the transducer can not be adjusted

so its face is parallel to the ground, re-

move the transducer and ratchets from

the bracket. Reinsert the ratchets into

the bracket, this time with the letter “B”

aligned with the dot stamped in the

bracket. Reassemble the transducer

and bracket and place it against the

transom.

5. Check to see if the transducer will ad-

just so its face is parallel with the ground.

Repeat this process until the transducer can

be adjusted so its face is parallel with the

ground.

C. Assembling the bracket

After determining the correct position for the

ratchets, loosely assemble the transducer and

bracket assembly.

Lock nut

Metal washer

Rubber washers

Ratchets

Metal washer

Bolt

Align dot and

letter "A".

dot

0.TWEETY INSTALL_SONAR_DSI.indd 3

9/14/2011 11:55:31 PM

Содержание DSI






















Результаты поиска

Содержание DSI

Отзывы:

Похожие инструкции для DSI

Бренды по названию

Популярные бренды

Lowrance DSI, Руководство по установке

Результаты поиска

Содержание DSI

Отзывы:

Похожие инструкции для DSI

Бренды по названию

Популярные бренды