Klein Marine Systems, Inc. HYDROCHART 3500 Скачать руководство пользователя

Страница: 46 / 86

4-8

CHAPTER 4 Maintenance

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

• RX PORT transducer cable to the RX PORT connector.

• TX PORT transducer cable to the TX PORT connector.

• RX STBD transducer cable to the RX STBD connector.

• TX STBD transducer cable to the TX STBD connector.

• Jumper cable to the DATA connector.

• Compass cable, if included, to the MRU connector.

• Sound velocity sensor cable, if included, to the S/V connector.

Loosely

attach the forward and aft fairings using all eighteen of the

M6 x 16 mm Phillips head screws and then tighten the screws securely.

The fully assembled Sonar Head Unit shown in Figure 4-12.

Figure 4-11:

Sonar Electronics Housing Connector End Cap Connectors

S/V

RX STBD

DATA

TX STBD

TX PORT

RX PORT

Compass

Содержание HYDROCHART 3500























































































Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды