Kingsman Fireplaces Marquis MQZDV3318 Скачать руководство пользователя страница 5

Страница: 5 / 64

Safety Screen Installation

Z Series

Screen with Side & Horizontal Angles

Hook Lower Clip onto glass door frame.

Press down and push upper clip under top glass door frame.

Contents of Kit:

[1] Safety Screen

[2] Side Angles

[2] Horizontal Angles

[12-16] DT Screws (Depending on screen size)

Assembly: Attach components with supplied
screws as shown.

⚠

WARNING:

Wait until unit is COMPLETELY

cool before touching glass or

attempting to install or remove

Child Safety Screens.

To install screens

hook bottom clip

onto glass door

frame, then press

down and push

upper clip under

top glass door

frame, then

release. Clip will

hook onto frame.

To remove

Safety

Screens

WAIT UNTIL

FIREPLACE IS

COMPLETELY

COOL.

Press down on

upper clips and

remove screen

from fireplace

glass door.

TOP VIEW

Upper Clip

Lower Clip

Upper Clip

NOTE: Screens are symmetrical from top to bottom.

CLIPS

Upper Clip

SIDE VIEW

Fireplace with

Screen

Содержание Marquis MQZDV3318

































































Результаты поиска

Содержание Marquis MQZDV3318

Отзывы:

Похожие инструкции для Marquis MQZDV3318

Бренды по названию

Популярные бренды

Kingsman Fireplaces Marquis MQZDV3318, Руководство по установке

Результаты поиска

Содержание Marquis MQZDV3318

Отзывы:

Похожие инструкции для Marquis MQZDV3318

Бренды по названию

Популярные бренды