manualshive.com logo in svg

Kikusui BIM1000 Series, Руководство пользователя

Поделиться
Скачать
Kikusui BIM1000 Series Скачать руководство пользователя страница 3

BIM1000 Series

User’s Manual

3

The BIM1000 Series Battery Impedance Meter can mea-
sure the internal resistance and voltage of motive power 
batteries quickly and accurately.
It can measure up to 1000 V and supports high-voltage, 
high-efficiency, low-resistance motive power batteries 
used in electric cars.
It is suitable for use in research and development and pro-
duction sites for motive power batteries and other similar 
products.

BIM1000 Series Lineup

Features

Supports high-voltage measurements

The BIM1030 up to 300 V and the BIM1100 can mea-
sure up to 1000 V. The internal battery resistance and 
voltage are measured simultaneously.

High-speed, high-accuracy measurement

The highest resolutions available are 0.1 μΩ and 10 μV. 
When the resistance and voltage are measured simulta-
neously, the measurements can take as little as about 
20 ms.

Measurement result judgment

Upper and lower limits can be set for the resistance and 
voltage measurements. Shows pass/fail judgment 
results on the display.

Interfaces for external devices

This product is standard equipped with a SIGNAL I/O 
connector, RS232C port, and USB port for controlling 
this instrument from a PC or other external devices. With 
RS232C, high-speed communication is possible at up to 
115200 bps.

Measurement logging and collective transfer func-
tion

Up to 500 pairs of resistance and voltage measurement 
logs can be stored. The logs can be transferred effi-
ciently using the collective transfer function.

• In this manual, the BIM1030 and BIM1100 Battery 

Impedance Meters are sometimes referred to as 
“BIM1000 Series”.

• The term “PC” is used to refer generally to both personal 

computers and workstations.

• The screen captures and illustrations used in this text 

may differ from the actual items.

• The following markings are used in this manual.

Indicates a potentially hazardous situation which, if ignored, 
could result in death or serious injury.

Indicates a potentially hazardous situation which, if ignored, 
may result in slight injury or damage to the product or other 
property.

Indicates information that you should know.

SHIFT+key name (blue letters under the key)

Indicates an operation that requires you to press a key indi-
cated in blue letters while holding down SHIFT.

 

>

Indicates the hierarchy of items you need to select. 
The item to the left of this symbol indicates a higher 
level item.

When using this product, be sure to observe the precau-
tions in the Safety Information manual. Items specific to 
this product are given below.

• To prevent electric shock, be sure to observe the fol-

lowing instructions. An electric shock may lead to a 
potentially fatal accident.

• Do not operate incorrectly.
• Do not touch the tip of the test lead connected to this 

product.

• When installing this product, be sure to observe the tem-

perature and humidity ranges indicated below.
Spec guaranteed temperature range: 18 °C to 28 °C 
(64 °F to 82 °F)
Spec guaranteed humidity range: 20 %rh to 80 %rh (no 
condensation)

• When storing this product, be sure to observe the tem-

perature and humidity ranges indicated below.
Storage temperature range: -10 °C to 60 °C (14 °F to 
140 °F)
Storage humidity range: 90 %rh or less (no condensa-
tion)

Model

Maximum measurement voltage

BIM1030

300 V

BIM1100

1000 V

Product Overview

Notations Used in This Manual

Safety Precautions

Notes on Usage

Содержание BIM1000 Series































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды