KidKraft Cedar Summit Adventure Ridge Playset Скачать руководство пользователя страница 77

Страница: 77 / 129

Hardware

10 x

#8 x 3” Wood Screw

Wood Parts

1 x

Tunnel MK Rail Right 1-3/8 x 4-1/2 x 90-1/4”

1 x

Tunnel MK Rail Left 1-3/8 x 4-1/2 x 90-1/4”

5 x Tennon Dowel 1-1/8 x 15-7/8”

342

343

341

Step 34: Monkey Rail Assembly

Part 1

Rail

Fig. 1.2

341

Fig. 34.1

Fig. 34.4

Fig. 34.2

Fig. 34.3

Pre-drill all pilot holes using a 1/8” drill bit before installing Wood Screws.
A:

Insert 5 (341) Dowels into both (342) Tunnel MK Rail Right and (343) Tunnel MK Rail Left. (Fig. 34.1and 34.2)

Make sure shoulder of dowel is against each rail before predrilling pilot holes. Drill 1/8” pilot holes through the

rails and into the dowels to prevent splitting. (Fig. 34.4)

Attach (341) Dowels to both rails with 2 (S4) #8 x3” Wood Screws per dowel. (Fig. 34.3)

Attach 1 (H5) Hex Bolt (with lock washer, flat washer and t-nut) to (343) Tunnel MK Rail Left and (342) Tunnel

MK Rail Right.

IMPORTANT! MAKE SURE THE BOLT IS ATTACHED TO MINIMIZE CHECKING OF WOOD.

(Fig. 34.1)

341

342

343

1/4” Lock

Washer

1/4” Flat

Washer

1/4”

T-Nut

Make sure the

T-Nuts are on

this side

Содержание Cedar Summit Adventure Ridge Playset


































































































































Результаты поиска

Содержание Cedar Summit Adventure Ridge Playset

Отзывы:

Бренды по названию

Популярные бренды

KidKraft Cedar Summit Adventure Ridge Playset, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cedar Summit Adventure Ridge Playset

Отзывы:

Бренды по названию

Популярные бренды