KidKraft Cedar Summit Adventure Ridge Playset Скачать руководство пользователя

Страница: 120 / 129

Step 67: Attach Swings

Other Parts

Using 1 Threaded Quick Link per chain, join 1 Long Swing Chain to each side of the Swing Belt Seat.

Make sure to close the Threaded Quick Link tightly using an adjustable wrench. (fig. 67.1 and 67.2).

Using 1 Threaded Clip per chain, join the Short Swing Chain to the Acro Bar and Acro Handle. Make sure

to close the Threaded Clip tightly using an adjustable wrench. (fig. 67.2 and 67.3)

Attach the other end of the swing chains to the Spring Loaded Quick Links attached to the Heavy Duty

Swing Hangers. (fig. 67.1)

1 x Acro Bar

2 x Acro Handle

2 x Swing Belt Seat

2 x Short Swing Chain

4 x Long Swing Chain

6 x Threaded Quick Link

Short

Swing

Chain

Swing Seat

Long Swing Chain

Threaded

Quick Link

Tighten Threaded Quick

Link using adjustable

wrench

Threaded Quick Links

attach to seat and Acro

bar.

Swing Seat

Acro Bar

Acro Handles

Fig. 67.2

Fig. 67.3

Fig. 67.1

Caution: Threaded Quick Links

must be installed with the gate

completely down covering

the threads and tighten as

instructed. (fig. 51.2)

120

Содержание Cedar Summit Adventure Ridge Playset


































































































































Результаты поиска

Содержание Cedar Summit Adventure Ridge Playset

Отзывы:

Похожие инструкции для Cedar Summit Adventure Ridge Playset

Бренды по названию

Популярные бренды

KidKraft Cedar Summit Adventure Ridge Playset, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cedar Summit Adventure Ridge Playset

Отзывы:

Похожие инструкции для Cedar Summit Adventure Ridge Playset

Бренды по названию

Популярные бренды