KidKraft Cedar Summit Adventure Ridge Playset Скачать руководство пользователя страница 48

Страница: 48 / 129

1 x

SW Block Angle 2-1/2 x 3 x 15”

1 x

Block SW 2-1/2 x 3 x 15”

2 x

SW Post 4 x 4 x 92”

Step 15: Swing Post Assembly

Part 1

153

152

151

Note: Keep all bolts from Step 15 series loose

until start of Step 17
A:

Place (151) SW Block Angle on top of (152)

Block SW and attach 2 Heavy L-Brackets on top of

(151) SW Block Angle feeding 2 (G17) 3/8 x 6” Hex

Bolts (with 2 flat washers, plastic formed washer and

lock nut) through both boards as shown in fig. 15.1

and 15.2.

Attach 3 (WB7) 5/16 x 3” Wafer Bolts (with flat

washer and t-nut) to all three holes in each (153)

SW Post as shown in fig. 15.3.

IMPORTANT!

MAKE SURE ALL 6 BOLTS ARE ATTACHED TO

MINIMIZE CHECKING OF WOOD.
C:

Place (151) SW Block Angle and (152) Block

SW assembly in between 2 (153) SW Post (Heavy

L-Brackets towards the outside). Place 1 Heavy

C-Bracket on the top (153) SW Post and attach with

1 (G26) 3/8 x 9-1/4” Hex Bolt (with 2 flat washers

and 1 lock nut), as shown in fig. 15.4.

2 x

3/8 x 6” Hex Bolt

(3/8” flat washer x 2, plastic formed washer & 3/8” lock nut)

1 x

3/8 x 9-1/4” Hex Bolt

(3/8” flat washer x 2 & 3/8” lock nut)

6 x

5/16 x 3” Wafer Bolt

(5/16” flat washer & 5/16” t-nut)

WB7

G17

Hardware

Wood Parts

G26

Other Parts

2 x Heavy L-Bracket
1 x Heavy C-Bracket

Fig. 15.4

Fig. 15.1

3/8” Flat

Washer

3/8”

Lock

Fig. 15.2

Fig. 15.3

Heavy

L-Bracket

3/8” Flat

Washer

5/16” T-Nut

Plastic

Formed

Washer

3/8” Flat

Washer

3/8”

Lock

Nut

Heavy L-Bracket

Bottom View

Top View

5/16” Flat

Washer

153

Heavy C-Bracket

152

x 6

G26

3/8” Flat

Washer

153

Notice Angle

Orientation

151

152

151

WB7

G17

Содержание Cedar Summit Adventure Ridge Playset


































































































































Результаты поиска

Содержание Cedar Summit Adventure Ridge Playset

Отзывы:

Бренды по названию

Популярные бренды

KidKraft Cedar Summit Adventure Ridge Playset, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cedar Summit Adventure Ridge Playset

Отзывы:

Бренды по названию

Популярные бренды