background image

Start-up 

 

3062.72-01 Rev. A

 

S e i t e  

|

 

25

 

 

Step 2a: Teach in the radio remote control:

 

 

Press and hold the UP or DOWN key for approx. 1 second in the 
close range. 

You hear 1 x „Klack-Klack“ 

 

 

The  radio  remote  control  is  now  taught-in  to  the  motor  and 
can be used. 

 

 

Step 2b: Delete radio remote control: 

 

ATTENTION!  All  radio  remote  controls taught-in  to the motor  will  be  deleted. It  is  not 
possible to delete a single radio remote control!

 

 

 

Activate learning mode as described in step 1. 

 

In the close range, press the UP or DOWN key and hold it down 
for approx. 5 seconds. The motor responds immediately. 

You hear 1 x „Klack-Klack“ 

 

 

Press and hold the button until the motor confirms the deletion 
of the radio remote control after 5 seconds. 

You hear 1 x „Klack-Klack“ 

 

6.2

 

Setting the end positions 

In your application, fixed mechanical end stops must be installed 
in  order  to  tell  the  motor  when  the  end  position  has  been 
reached.  When  the  respective  end  position  is  reached,  the 
motor must move against the end stop in order to switch off via 
the integrated torque monitoring. If there are no end stops, the 
drive system and your application may be damaged. 

Содержание Drive System 3062




































Отзывы: