ATE-DMG 020613
B-11
racy of the measurement if nn,nn is added after the question mark; the power supply accepts this for-
mat but sets the command warning bit (13) in the status questionable register and ignores the extra
characters. (See example, Figure B-1.)
B.42 OUTPut[:STATe]
COMMAND
OUTP
Syntax:
Short Form: OUTP[:STAT] <boolean>
Long Form: OUTPut[:STATe] <boolean>
<boolean>=(0 or OFF, 1 or ON)
Description:
Enables or disables the power supply output.
Upon power up the output is enabled (OUTP ON).
When OUTP OFF is executed, the programmed values of voltage and current are saved, then voltage
and current are programmed to 0. When OUTP ON is executed, the power supply output is restored to
the previously saved programmed values. The saved values of voltage and current can be viewed by
VOLT? and CURR? queries. Related Commands: OUTP?. (See example, Figure B-1.)
B.43 OUTPut[:STATe]
QUERY
OUTP?
Syntax:
Short Form: OUTP[:STAT]?
Long Form: OUTPut[:STATe]?
Return Value: <int_value> (0 or 1)
Description:
Indicates whether power supply output is enabled or disabled.
Returns 0 if output disabled,
returns 1 if output enabled. Related Commands: OUTP. (See example, Figure B-1.)
B.44 OUTPut:PROTection:DELay COMMAND
OUTP:PROT:DEL
Syntax
:
Short Form: OUTP:PROT:DEL <n.n>
Long Form: OUTPut:PROTection:DELay <n.n>
where n.n = seconds
Description:
Delays tripping of overvoltage/overcurrent protection.
The overvoltage and overcurrent protection
can be programmed to trip immediately upon detection of an overvoltage/overcurrent condition, or can
be delayed approximately 8 seconds. This delay is set in increments of 0.033 milliseconds If delay is
programmed, overcurrent/overvoltage protection trips only if condition still present at end of delay. A
count of 0 means no delay, the maximum delay possible is 8.50 seconds.
B.45 OUTPut:PROTection:DELay QUERY
OUTP:PROT:DEL?
Syntax
:
Short Form: OUTP:PROT:DEL?
Long Form: OUTPut:PROTection:DELay?
Return Value: <integer 1 to 8.5>
Description:
Returns value of overvoltage/overcurrent delay.
A count of 0 means no delay, The maximum value
is 8.5. The delay constants are set in -.033 milliseconds per internal value. Related Commands:
OUTP:PROT:DEL. (See example, Figure B-5.)
B.46 PROGram:SELect:STATe COMMAND
PROG:SEL:STAT
Syntax
:
Short Form: PROG:SEL:STAT {RUN | STOP}
Long Form: PROGram:SELect:STATe {RUN | STOP}
Description:
Starts or stops user programmed sequence.
Program sequence is preprogrammed using LIST
commands, starting address is established by LIST:SEQ:STAR. When PROG:SEL:STAT command is
executed the keyboard is locked until the program stops running. *RST command aborts a program
that is running. Related commands: PROG:SEL:STAT?, LIST:CURR, LIST:CURR:PROT, LIST:VOLT,
LIST:VOLT:PROT, LIST:DWEL, LIST:SEQ:NEXT, LIST:SEQ:STAR
B.47 PROGram:SELect:STATe? QUERY
PROG:SEL:STAT?
Syntax
:
Short Form: PROG:SEL:STAT?
Long Form: PROGram:SELect:STATe?
Return value: <boolean> (0 = stopped, 1 = running)
Description:
Indicates status of user programmed sequence.
1 returned when program is running. 0 returned
when program is stopped. Related commands: PROG:STAT
Содержание ATE 100-10DMG
