KEP MMI-1500 Скачать руководство пользователя

Страница: 295 / 306

287

16.40 SIEMENS S7/300 MMI ADAPTOR

Siemens MMI adapter (Siemens Part# 6ES7-972-0CA10-0XA0) required.

16.40.1 HMI Setting

Communication parameters must be set the same as those of the PLC. The following settings are recommended.

Parameter

Recommended Setting Notes

Serial I/F port

RS-232

Options: RS-232, RS-485 default/2W/4W – Dependant on PLC
hardware

Baud rate

9600

Options: 9600, 19200, 38400, 57600, 115200 - Must match PLC port
setting

Parity

Odd

Options: Odd, Even, None - Must match PLC port setting

Data bits

Options: 7, 8 - Must match PLC port setting

Stop bits

Options: 1, 2 - Must match PLC port setting

HMI station No.

Not used

PLC station No.

Options: 0-255 - As per PLC setting

Comm. delay (10msec) 0

Request delay: 0~999 @10 milliseconds. Use when the PLC requires a
delay between requests. Not implemented in simulation mode.

16.40.2 PLC Setting

S300 Station number (Station Number) must be 02 and DB10 must be created.

Communication parameters must be the same as those of the MMI.

Compatible with:

Siemens S7-300 Series: CPU 312, 313, 314, 315, 316, 318 (using an MMI adapter from Siemens)

16.40.3 Wiring

Adapter cable to go from HMI to MMI Adapter cable.

DO NOT PLUG THIS CABLE DIRECTLY INTO THE PLC!

16.40.3.1

Wiring for cable connections using

Siemens S7-300

CPU’s

with

MMI adapter

RS232 D-Sub 9 Male

Socket ports.
KEP Part#:

SMICABDF1-05

(D-Sub 9 Male Socket to D-Sub 9 Female Plug Cable)

HMI PLC[RS-232]

Connect to Siemens MMI adapter

RS-232 port

2 TD

2 RD

3 RD

3 TD

5 GND

5 GND
7 RTS

8 CTS

Shield

Earth Ground

Note:

Graphic representation may not reflect the actual appearance of the finished cable.

16.40.4 Device address

Bit/Word

Type

Address Format

Range

Notes

ddddo

dddd: 0~4095 o: 0~7 Input Bits, Word portion is decimal, bit portion is octal

ddddo

dddd: 0~4095 o: 0~7 Output Bits, Word portion is decimal, bit portion is octal

ddddo

dddd: 0~4095 o: 0~7 Internal Bits, Word portion is decimal, bit portion is octal

DB10

dddd

dddd: 0~8192

Data Words, Addresses must be even numbers 0,2,4,…
etc.

Note:

Do not write to Data words that do not exist as this may cause PLC malfunction.

Содержание MMI-1500



















































































































































































































































































































Результаты поиска

Содержание MMI-1500

Отзывы:

Похожие инструкции для MMI-1500

Бренды по названию

Популярные бренды

KEP MMI-1500, Руководство по установке и эксплуатации

Результаты поиска

Содержание MMI-1500

Отзывы:

Похожие инструкции для MMI-1500

Бренды по названию

Популярные бренды