KEP MMI-1500 Скачать руководство пользователя страница 291

Страница: 291 / 306

283

16.36.3.2

Wiring for cable connections using

SAIA PCD CPU

with

PGU Port

Type

RS-232

S-Bus

D-Sub 9

Female Plug ports.
KEP Part#: (Not Available) (D-Sub 9 Male Socket to D-Sub 9 Male Socket Cable)

HMI PLC[RS-232]

Connect to SAIA PCD CPU RS-232 Port 0

2 TD

2 RXD

3 RD

3 TXD

5 GND

5 GND
7 RTS

8 CTS

Shield

Earth Ground

Note:

Graphic representation may not reflect the actual appearance of the finished cable.

16.36.3.3

Wiring for cable connections using

SAIA PCD 1 CPU

with

Port 1

-Type

RS-485

S-Bus

ports.

KEP Part#: (Not Available) (D-Sub 9 Male Socket to PCD Cable)

HMI PLC[RS-232]

Connect to SAIA PCD 1 port

1 RX-

11 RX-

2 RX+

12 RX+
Shield

Earth Ground

Graphic not available

16.36.3.4

Wiring for cable connections using

SAIA PCD 2 CPU

with

Port 0

-Type

RS-485

S-Bus

ports.

KEP Part#: (Not Available) (D-Sub 9 Male Socket to PCD Cable)

HMI PLC[RS-232]

Connect to SAIA PCD 0 port

1 RX-

29 RX-

2 RX+

28 RX+
Shield

Earth Ground

Graphic not available

16.36.4 Device address

Bit/Word

Type

Address

Format

Range

Notes

Flag

dddd

ddd: 0~ 8191

Internal Relay

Input

ddd

ddd: 0~ 511

Input Relay

Output

ddd

ddd: 0~ 511

Output Relay

dddd

dddd: 0~4095

Internal 32 bit Register

Note:

Double Word

Counter

dddd

dddd: 0~1599

Counter Accumulator

Note:

Double Word

Timer

dddd

dddd: 0~450

Timer Accumulator

Note:

Double Word

Reg_Word dddd

dddd: 0~4095

Internal 16 bit Register reads 16 LSB data. 16 MSB’s
must be zeroed. Data range is –32768 to +32767

Reg_Float dddd

dddd: 0~4095

Internal 32 bit Floating Point Register

Note:

Double Word

Note:

Reg_Float: SAIA PCD uses non-standard floating-point format. Before sending and after received data from PCD, the

driver converts the format. This causes an over flow error when the exponent is too large.

Содержание MMI-1500



















































































































































































































































































































Результаты поиска

Содержание MMI-1500

Отзывы:

Бренды по названию

Популярные бренды

KEP MMI-1500, Руководство по установке и эксплуатации

Результаты поиска

Содержание MMI-1500

Отзывы:

Бренды по названию

Популярные бренды