KENT 908 7113 020 Скачать руководство пользователя

Страница: 8 / 58

GENERAL INFORMATION

ENGLISH

SERVICE MANUAL

909 6577 000(4)2009-11

Razor SV17 - Razor E17

120 VAC GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric

current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and

grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all

local codes and ordinances.

WARNING!

The machine must be used with an extension power cord as follows:

minimum length 15 feet

–

type S, or ST, or SO, or STO, or STW

–

minimum rate 300V 140/167°F (60/75°C)

–

DANGER!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check

–

with a qualified electrician or service person if you are in doubt as to whether the outlet is properly

grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

This appliance is for use on a nominal 120 V circuit, and has a grounding plug that looks like the plug

–

(B, Fig. 1). A temporary adapter (B and C) may be used to connect this plug to a 2-pole receptacle (B), if

a properly grounded outlet is not available. The temporary adapter should be used only until a properly

grounded outlet (A) can be installed by a qualified electrician. The green-colored rigid ear, tab, or the like

extending from the adapter must be connected to a permanent ground such as a properly grounded outlet

box cover. Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are

not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

–

The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire must

–

be attached to the grounding pin only.

Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs

–

and outlets. DO NOT use extension cords more than 50 feet (15 m) long.

S310183A

DIMENSIONS (

Razor SV17

Razor E17

)

720 mm (28,3 in)

1120 mm (44.0 in)

570 mm (22,4 in)

860 - 1105 mm (33.8 - 43.5 in)

Содержание 908 7113 020



























































Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды

KENT 908 7113 020, Руководство по обслуживанию

Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды