KENT 908 7113 020 Скачать руководство пользователя

Страница: 38 / 58

ELECTRICAL SYSTEM

ENGLISH

SERVICE MANUAL

909 6577 000(4)2009-11

Razor SV17 - Razor E17

ELECTRICAL SYSTEM
(WET OR GEL) BATTERY REMOVAL/INSTALLATION AND SETTING [Razor SV17]

Disassembly

Check that the switches (5 and 6) are turned to “0”.

If there is recovery water in the tank (43), drain it through the hose (22).

Disconnect the vacuum hose (29) from the squeegee (17).

Open the cover (12).

Grasp the recovery water tank (A) in the area (B) and lift it, as shown in the figure, then disconnect the vacuum hose (C) from

the tank and remove the tank (A) together with the hoses (D) and (E).

Disconnect the battery terminals (50).

Remove the batteries (50).

Setting (WET or GEL) before installation

If the type of battery chosen to be installed is different from the removed one (not WET but GEL, or viceversa), before

installing and connecting the new batteries, the machine electronic board setting must be performed according to the following

procedure.

Remove the screws (F) and carefully pull out the electrical component box cover (G).

Set the microswitch (H) to WET or GEL position according to the type of battery that is to be installed.

10.

WARNING!

Do not move the adjacent switch (I).

Reinstall the electrical component box cover (G) and tighten the screws (F).

11.

Battery assembly

Once the setting is performed, install the batteries on the machine according to the diagram (51).

12.

Connect the battery terminals (50).

13.

Battery charger

Charge the batteries.

14.

Reset

Carry out steps from 3 to 5 in the reverse order.

15.

S301369

Содержание 908 7113 020



























































Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды

KENT 908 7113 020, Руководство по обслуживанию

Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды