KENT 908 7113 020 Скачать руководство пользователя | Manualshive

Страница: 34 / 58

background image

OTHER SYSTEMS

ENGLISH

SERVICE MANUAL

32

909 6577 000(4)2009-11

Razor SV17 - Razor E17

OTHER SYSTEMS
MACHINE SPEED ADJUSTMENT [Razor SV17 - Razor E17]

Check that the switches (5 and 6) are turned to “0”.

1.

If there is recovery water in the tank (43), drain it through the hose (22).

2.

Disconnect the vacuum hose (29) from the squeegee (17).

3.

Open the cover (12).

4.

Grasp the recovery water tank (A) in the area (B) and lift it, as shown in the figure, then disconnect the vacuum hose (C) from

5.

the tank and remove the tank (A) together with the hoses (D) and (E).

Adjust the machine speed by means of the screw (53), according to the following procedure:

6.

Loosen the screw (57) on the right side of the machine, by turning it counter-clockwise.

•

Turn the adjusting screw (53) counter-clockwise to increase the machine speed.

•

Turn the adjusting screw (53) clockwise to decrease the machine speed.

•

After adjusting, tighten the screw (57).

•

Carry out steps from 3 to 5 in the reverse order.

7.

With the machine ready to operate, carry out hands-on tests of the machine speed and, if other adjustments are necessary,

8.

repeat steps 1 to 8.

S301369

«
...
32
33
34
35
36
...
»

Содержание 908 7113 020



























































Отзывы:

Нет отзывов

Похожие инструкции для 908 7113 020

Бренд: Gardenline Страницы: 19

Бренд: Toro Страницы: 24

Бренд: Little Wonder Страницы: 54

Бренд: ebm-papst Страницы: 11

Бренд: Echo Страницы: 30

Бренд: Best Страницы: 16

Бренд: Black Max Страницы: 36

Бренд: Billy Goat Страницы: 12

Бренд: Siemens Страницы: 8

Бренд: Troy-Bilt Страницы: 32

Бренд: SNOWJOE Страницы: 20

Бренд: Troy-Bilt Страницы: 48

Бренд: Troy-Bilt Страницы: 52

Бренд: Troy-Bilt Страницы: 56

Бренд: Troy-Bilt Страницы: 60

Бренд: White Outdoor Страницы: 52

Бренд: Echo Страницы: 28

Бренд: Worx Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды