KENT 908 7113 020 Скачать руководство пользователя

Страница: 4 / 58

GENERAL INFORMATION

ENGLISH

SERVICE MANUAL

909 6577 000(4)2009-11

Razor SV17 - Razor E17

GENERAL INFORMATION

NOTE

Forward and backward, front and rear, left and right are intended with reference to the operator’s position.

MACHINE LIFTING

WARNING!

Do not work under the lifted machine without supporting it with safety stands.

MACHINE TRANSPORTATION

WARNING!

Before transporting the machine, make sure that:

All doors and cases are closed

–

The battery connector, if present, is disconnected

–

The machine is securely fastened to the means of transport

–

OTHER REFERENCE MANUALS

The following manuals are available at Kent Literature Service Department:

Razor SV17 Instructions for Use - Form Number 909 5853 000

Razor SV17 Spare Parts List - Form Number 909 5854 000

Razor SV17 Installation Instruction for Battery charger kit- Form Number 9097050000

Razor SV17 - Razor E17 Installation Instructions for Curved squeegee kit - Form Number 909 6450 000

Razor SV17 - Razor E17 Installation Instructions for Rubber shock absorber kit - Form Number 909 6227 000

Razor SV17 - Razor E17 Installation instruction solenoid valve kit - Form Number 9097873000

Razor E17 Instructions for Use - Form Number 909 5855 000

Razor E17 Spare Parts List - Form Number 909 5856 000

SAFETY

Kent uses the following symbols to indicate potentially dangerous situations. Always read this information carefully and take all

necessary precautions to safeguard people and property.

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people or damage to objects.

CAUTION!

It indicates a remark related to important or useful functions.

Pay particular attention to the paragraphs marked by this symbol.

NOTE

It indicates a caution or a remark related to important or useful functions.

CONSULTATION

It indicates the necessity to refer to the User Manual before performing any procedure.

Содержание 908 7113 020



























































Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды

KENT 908 7113 020, Руководство по обслуживанию

Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды